Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- RIDGID HIGH PERFORMANCE THREAD CUTTING OIL
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricant for Industrial use
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
RIDGE TOOL EUROPE
manufacturer
INTERLEUVENLAAN, RESEARCH PARK, 3001 LEUVEN, BELGIUM
+32 (0) 16380211
Emergency Contacts
Emergency Contact
++49/2947/88100
During normal opening times
Customer Service
+32 (0) 16380211
Office hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Zinc dialkyldithiophosphat | --- | 0.1 - 0.3% | Yes |
| Petroleum gases, liquefied, sweetened EC: 270-705-8 | 68476-86-8 | 25 - 50% | Yes |
For the wording of the listed risk phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately rinse with water.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Rinse out mouth and then drink plenty of water.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, Sand, Carbon dioxide, CO2, extinguishing powder.
Water with full jet
During heating or in case of fire poisonous gases are produced.
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep away from ignition sources. Ensure adequate ventilation. Wear protective equipment. Keep unprotected persons away.
Do not allow product to reach sewage system or any water course. Do not allow to enter sewers/ surface or ground water.
Do not flush with water or aqueous cleansing agents
Related Products
Similar products with comparable safety profiles
RIDGID High Performance Thread Cutting Oil
---
RIDGID High Performance Thread Cutting Oil
---
RIDGID Dark Thread Cutting Oil
---
RIDGID Dark Thread Cutting Oil
---
RIDGID Dark Thread Cutting Oil
---
RIDGID Extreme Performance Thread Cutting Oil (United States)
---
RIDGID Dark Thread Cutting Oil (United States)
---
RONOL Thread Cutting Oil
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Store in cool, dry place in tightly closed receptacles. Open and handle receptacle with care.
Store in a cool location. Observe official regulations on storing packagings with pressurized containers. Store under lock and key and out of the reach of children. Store in cool, dry conditions in well sealed receptacles. Keep container tightly sealed. Do not seal receptacle gas tight. Protect from heat and direct sunlight.
Do not spray onto a naked flame or any incandescent material. Keep ignition sources away - Do not smoke. Protect against electrostatic charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Recommendation: Chemical resistant protective gloves (EN 374). The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles. Use safety glasses according to EN 166 : 2001.
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device. Use suitable respiratory protective device in case of insufficient ventilation.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
Reacts with strong oxidants and strong reducing agents under severe heat.
No dangerous reactions known.
Temperatures above 50 °C can result in breakage of the container
No further relevant information available.
Emergence of flammable gases / vapors on contact with strong oxidizing agent's possible.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed together with household garbage.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2
- Packing Group
- Void
Warning: Gases.
Warning: Gases.
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Labelling according to EU guidelines. The product has been classified and marked in accordance with EU Directives / Ordinance on Hazardous Materials.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for RIDGID HIGH PERFORMANCE THREAD CUTTING OIL?
The signal word is na: r-phrases.
What is the physical form of RIDGID HIGH PERFORMANCE THREAD CUTTING OIL?
RIDGID HIGH PERFORMANCE THREAD CUTTING OIL is a aerosol with brown color. It has characteristic odor.
What is the solubility of RIDGID HIGH PERFORMANCE THREAD CUTTING OIL?
Not miscible or difficult to mix.
What is RIDGID HIGH PERFORMANCE THREAD CUTTING OIL used for?
Lubricant for Industrial use
What is the melting point of RIDGID HIGH PERFORMANCE THREAD CUTTING OIL?
The melting point is Undetermined. and the boiling point is -44 °C.