Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
- Product Code
- AP-N26
Regulatory Identifiers
- CAS Number
- N/A
- UFI Code
- KH45-K06Q-800A-VTPW
Identified Uses
Laboratory use
Uses advised against
No information available
Manufacturers & Suppliers
LGC Limited
national supplier
Queens Road Teddington Middlesex TW11 0LY
+44 (0) 20 8943 7000
www.lgcstandards.com
Emergency Contacts
CHEMTREC
1-800-424-9300
CHEMTREC
+1 703-741-5970
Emergency Contact
112
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of organic compounds.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 1-Deceen, dimeer, gehydrogeneerd EC: 500-228-5 | 68649-11-6 | 40 - 60% | Yes |
Acute Toxicity Estimate: If LD50/LC50 data is not available or does not correspond to the classification category, then the appropriate conversion value from CLP Annex I, Table 3.1.2, is used to calculate the acute toxicity estimate (ATEmix) for classifying a mixture based on its components.
Notes
Full text of H- and EUH-phrases: see section 16. This product does not contain candidate substances of very high concern at a concentration >=0.1% (Regulation (EC) No. 1907/2006 (REACH), Article 59).
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove to fresh air. If symptoms persist, call a doctor. If breathing has stopped, give artificial respiration. Get medical attention immediately.
Symptoms: Coughing and/ or wheezing. Difficulty in breathing.
Wash skin with soap and water. In the case of skin irritation or allergic reactions see a doctor.
Rinse thoroughly with plenty of water for at least 15 minutes, lifting lower and upper eyelids. Consult a doctor.
Do NOT induce vomiting. Rinse mouth. Never give anything by mouth to an unconscious person. Get medical attention.
Immediate Medical Attention
If symptoms persist, call a doctor. If breathing has stopped, get medical attention immediately. Consult a doctor. In the case of skin irritation or allergic reactions see a doctor. Get medical attention. Treat symptomatically.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Viscosity Reference Standard General Purpose Type N7.5, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
UFI: A095-W03C-6002-8K08
Viscosity Reference Standard General Purpose Type N415, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
---
Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
UFI: HJ25-X0AK-600X-NY9E
General Purpose Viscosity Standard – Synthetic Base Oil
---
Silicone Viscosity Standards (5 cSt to 100,000 cSt)
---
225 N (High viscosity grade)
CAS: 64742-54-7
Mineral Oil standard VSL-001
---
CM pre-fill Standard T/V 190ml
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The protective gloves to be used must comply with the specifications of EC Directive 89/686/EEC and the related standard EN374. Wear protective nitrile rubber gloves.
Avoid contact with eyes. Wear safety glasses with side shields (or goggles).
No protective equipment is needed under normal use conditions. If exposure limits are exceeded or irritation is experienced, ventilation and evacuation may be required.
Wear suitable protective clothing.
Do not allow into any sewer, on the ground or into any body of water.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Not regulated
- Shipping Name
- Not regulated
- Packing Group
- Not regulated
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
The signal word is warning.
What is the physical form of Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded is a liquid appearing as liquid with colourless color. It has slight. odor.
What is the solubility of Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
No data available
What is Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded used for?
Laboratory use
What are the hazard statements for Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
This substance has 1 hazard statement:
- H332: Harmful if inhaled
What is the melting point of Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
The melting point is No data available and the boiling point is No data available.