Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
- Product Code
- AP-S3
Regulatory Identifiers
- CAS Number
- N/A
- UFI Code
- HJ25-X0AK-600X-NY9E
Identified Uses
Laboratory use
Uses advised against
No information available
Manufacturers & Suppliers
LGC Limited
Queens Road Teddington Middlesex TW11 0LY UNITED KINGDOM
+44 (0) 20 8943 7000
www.lgcstandards.com
Emergency Contacts
CHEMTREC
1-800-424-9300
CHEMTREC
+1 703-741-5970
Emergency Contact
112
Emergency Contact
(+352) 8002 5500
24/7
FR, NL, EN
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS08
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of organic compounds.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Kerosine : distillates, hydrotreated light (D94/69 p1249) EC: 265-149-8 | 64742-47-8 | 80 - 100% | Yes |
| White mineral oil, petroleum EC: 232-455-8 | 8042-47-5 | 20 - 40% | Yes |
Full text of H- and EUH-phrases: see section 16 Acute Toxicity Estimate If LD50/LC50 data is not available or does not correspond to the classification category, then the appropriate conversion value from CLP Annex I, Table 3.1.2, is used to calculate the acute toxicity estimate (ATEmix) for classifying a mixture based on its components
Notes
This product does not contain candidate substances of very high concern at a concentration >=0.1% (Regulation (EC) No. 1907/2006 (REACH), Article 59)
First Aid Measures
Emergency procedures for chemical exposure incidents
If breathing has stopped, give artificial respiration. Get medical attention immediately. Remove to fresh air. Avoid direct contact with skin. Use barrier to give mouth-to-mouth resuscitation. If breathing is difficult, (trained personnel should) give oxygen. Get immediate medical advice/attention.
Symptoms: Aspiration into lungs can produce severe lung damage. Delayed pulmonary edema may occur.
Wash skin with soap and water. In the case of skin irritation or allergic reactions see a doctor.
Symptoms: skin irritation or allergic reactions
Rinse thoroughly with plenty of water for at least 15 minutes, lifting lower and upper eyelids. Consult a doctor.
Do NOT induce vomiting. If vomiting occurs spontaneously, keep head below hips to prevent aspiration. Rinse mouth. Never give anything by mouth to an unconscious person. Get immediate medical advice/attention.
Symptoms: ASPIRATION HAZARD IF SWALLOWED - CAN ENTER LUNGS AND CAUSE DAMAGE.
Immediate Medical Attention
Immediate medical attention is required. Get medical attention immediately. Get immediate medical advice/attention.
Medical Treatment
Because of the danger of aspiration, emesis or gastric lavage should not be used unless the risk is justified by the presence of additional toxic substances.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Viscosity Reference Standard General Purpose Type N7.5, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
UFI: A095-W03C-6002-8K08
Viscosity Reference Standard General Purpose Type N415, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
---
Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
UFI: KH45-K06Q-800A-VTPW
General Purpose Viscosity Standard – Synthetic Base Oil
---
Silicone Viscosity Standards (5 cSt to 100,000 cSt)
---
225 N (High viscosity grade)
CAS: 64742-54-7
Mineral Oil standard VSL-001
---
CM pre-fill Standard T/V 190ml
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
If exposure limits are exceeded or irritation is experienced, ventilation and evacuation may be required.
The protective gloves to be used must comply with the specifications of EC Directive 89/686/EEC and the related standard EN374. Wear protective nitrile rubber gloves.
If splashes are likely to occur, wear safety glasses with side-shields. Avoid contact with eyes. Wear safety glasses with side shields (or goggles).
No protective equipment is needed under normal use conditions. If exposure limits are exceeded or irritation is experienced, ventilation and evacuation may be required.
Wear suitable protective clothing.
Do not allow into any sewer, on the ground or into any body of water.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
The signal word is danger.
What is the physical form of Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded is a liquid appearing as liquid with colourless color. It has characteristic. odor.
What is the solubility of Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
No data available
What is Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded used for?
Laboratory use
What are the hazard statements for Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
This substance has 1 hazard statement:
- H304: May be fatal if swallowed and enters airways
What is the melting point of Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded?
The melting point is No data available and the boiling point is No data available.