Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- CM pre-fill Standard T/V 190ml
- Product Code
- 738074
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
SU22 Professional uses: Public domain (administration, education, entertainment, services, craftsmen) SU21 Consumer uses: Private households / general public / consumers PC9a Coatings and paints, thinners, paint removers PROC7 Industrial spraying PROC11 Non industrial spraying Lacquer
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
MOTIP DUPLI GmbH
manufacturer
Kurt Vogelsang Strasse 6 D-74855 Hamersheim
+49/6266/75-0
Emergency Contacts
Emergency Contact
+49 6266-75-310
Mo - Th 08:00 am - 04:00 pm, Fr 08:00 am - 00:30 pm
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| DIMETHYL ETHER EC: 204-065-8 | 115-10-6 | 75 - 100% | Yes |
| Isopropanol EC: 200-661-7 | 67-63-0 | 12.5 - 20% | Yes |
The content of Benzene (EINECS-Nr. 200-753-7) in the ingredients is less than 0,1% (Note P Annex 1A 1272/2008 EU), so the classification as carcinogen need not to apply. For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Drink plenty of water and provide fresh air. Call for a doctor immediately.
Immediate Medical Attention
No further relevant information available.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
COLORMATIC PRE-FILL STANDARD 275 ML
---
CU-800 - 300 ML
UFI: HCM8-9049-0002-QJ25
COLORMARK LINEMARKER BLUE 500 ML
---
COLORMARK LINEMARKER WHITE 500 ML
---
Viscosity Reference Standard General Purpose Type N7.5, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
UFI: A095-W03C-6002-8K08
Viscosity Reference Standard General Purpose Type S3, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
UFI: HJ25-X0AK-600X-NY9E
Viscosity Reference Standard General Purpose Type N26, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
UFI: KH45-K06Q-800A-VTPW
Viscosity Reference Standard General Purpose Type N415, UKAS ISO 17025 / ISO 17034, 500 mL / AP Dual-branded
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
In case of contact with spray dust protective gloves made of butyl shoud be used (min. 0.4 mm thick), e.g. KCL Camatril, article no. 898 or similar products. Solvent resistant gloves. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: Butyl rubber, BR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: Butyl rubber gloves with a thickness of 0.4 mm are resistant to: Acetone: 480 min, Butyl acetate: 60 min, Ethyl acetate: 170 min, Xylene: 42 min. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed. For the permanent contact in work areas without heightened risk of injury (e.g. Laboratory) gloves made of the following material are suitable: Natural rubber, NR.
Not necessary if room is well-ventilated. In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1950
- Shipping Name
- AEROSOLS
- Packing Group
- not regulated
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for CM pre-fill Standard T/V 190ml?
The signal word is danger.
What is the physical form of CM pre-fill Standard T/V 190ml?
CM pre-fill Standard T/V 190ml is a aerosol with according to product specification color. It has characteristic odor.
What is the solubility of CM pre-fill Standard T/V 190ml?
Not miscible or difficult to mix.
What is CM pre-fill Standard T/V 190ml used for?
SU22 Professional uses: Public domain (administration, education, entertainment, services, craftsmen) SU21 Consumer uses: Private households / general public / consumers PC9a Coatings and paints, thinners, paint removers PROC7 Industrial spraying PROC11 Non industrial spraying Lacquer
What are the hazard statements for CM pre-fill Standard T/V 190ml?
This substance has 3 hazard statements:
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
- H319: Causes serious eye irritation.
What is the melting point of CM pre-fill Standard T/V 190ml?
The melting point is Undetermined. and the boiling point is Not applicable, as aerosol..