Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- 3M 50598 Premium Body Filler
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Automotive.
Manufacturers & Suppliers
3M United Kingdom PLC
manufacturer
3M Centre, Cain Rd, Bracknell, Berkshire, RG12 8HT
www.3M.com/uk
Emergency Contacts
Emergency Contact
+44 (0)1344 858 000
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
3MTM Blue Cream Hardener
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Limestone | 1317-65-3 | 10 - 30% | No |
| Styrene Monomer | 100-42-5 | 10 - 30% | Yes |
| Polyester resin | --- | 10 - 30% | No |
| Talc | 14807-96-6 | 10 - 30% | No |
| Unsaturated polyester resin | --- | 7 - 13% | No |
| Magnesium Carbonate | 546-93-0 | 3 - 7% | No |
| Titanium Dioxide | 13463-67-7 | 1 - 5% | No |
| Barium Sulfate | 7727-43-7 | 1 - 5% | No |
| Glass, oxide, chemicals | 65997-17-3 | 1 - 5% | No |
| Quaternary ammonium compounds (bis) hydrogenated tallow alkyl dimethyl, salts with montmorillonite | --- | 0.5 - 1.5% | No |
| Quartz | 14808-60-7 | 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove person to fresh air. If signs/symptoms develop, get medical attention.
Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse.
Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
3M 08080 Auto Adhesive Aerosol
---
3M Spray 74 Foam Adhesive
---
3M™ Polyether Adhesive - New Formulation
---
SMOOTH 7 BODY FILLER FOR DEEP REPAIRS (SM/7)
---
3M™ Finesse-It™ Polish - Final Finish
---
3M Unitek Transbond XT Primer
---
3M Unitek Transbond XT Primer
---
3M 51815, 51816, 51818 Fast Cut Plus Extreme
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use with appropriate local exhaust ventilation. Use in an enclosed process area is recommended. Provide appropriate local exhaust for cutting, grinding, sanding or machining. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or airborne particles. If ventilation is not adequate, use respiratory protection equipment.
Gloves made from the following material(s) are recommended: Polyehtylene or ethylene vinyl alcohol.
Avoid eye contact with vapours, mists, or spray. To minimise the risk of injury to face and eyes, always wear eye and face protection when working at sanding or grinding operations or when near such operations. The following eye protection(s) are recommended: Safety glasses with side shields. Indirect vented goggles.
Avoid breathing of dust created by cutting, sanding, grinding or machining. Do not breathe vapours. Select one of the following approved respirators based on airborne concentration of contaminants and in accordance with regulations: Half facepiece or fullface air-purifying respirator with organic vapour cartridges and P2 particulate prefilters. Consult the current 3M Respiratory Selection Guide for additional information or contact 3M for technical assistance.
Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
No data available.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN3108
- Shipping Name
- Organic Peroxide Type E, Solid, (Dibenzoyl peroxide (as a paste), <= 52%)
- Transport Class
- 5.2
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for 3M 50598 Premium Body Filler?
The signal word is no signal word.
What is the physical form of 3M 50598 Premium Body Filler?
3M 50598 Premium Body Filler is a liquid appearing as light grey paste with light grey color. It has pungent solvent odour odor.
What is the solubility of 3M 50598 Premium Body Filler?
Negligible
What is 3M 50598 Premium Body Filler used for?
Automotive.
What is the melting point of 3M 50598 Premium Body Filler?
The melting point is No data available and the boiling point is 145 °C.