Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Titanium(IV) oxide
- Product Code
- 718467
- Chemical Name
- Titanium(IV) oxide
Regulatory Identifiers
- CAS Number
- 13463-67-7 Check regulations →
- REACH No.
- A registration number is not available for this substance as the substance or its uses are exempted from registration or the annual tonnage does not require a registration.
Identified Uses
Laboratory chemicals, Manufacture of substances
Manufacturers & Suppliers
Merck Life Science BV/SRL
manufacturer
Brusselsesteenweg 288, B-3090 OVERIJSE
+32 (0)3 899-1301
Emergency Contacts
CHEMTREC
+(32) 28 083237
Anti-poison centre
070 245245
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Formula : TiO2 Molecular weight : 79,87 g/mol CAS-No. : 13463-67-7 EC-No. : 236-675-5
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| TiO2 EC: 236-675-5 | 13463-67-7 | --- | No |
Notes
No components need to be disclosed according to the applicable regulations.
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
For this substance/mixture no limitations of extinguishing agents are given.
Titanium/titanium oxides. Not combustible. Ambient fire may liberate hazardous vapours.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
No special precautionary measures necessary.
Clean up affected area.
Related Products
Similar products with comparable safety profiles
Titanium(IV) oxide
CAS: 13463-67-7
Titanium(IV) oxide, mixture of rutile and anatase
CAS: 13463-67-7
Titanium dioxide
CAS: 13463-67-7
Titanium(IV) chloride
CAS: 7550-45-0
Titanium
CAS: 7440-32-6
Tin(IV) oxide
CAS: 18282-10-5
Tungsten(VI) oxide
CAS: 1314-35-8
Tungsten(VI) oxide
CAS: 1314-35-8
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only in area provided with appropriate exhaust ventilation.
Tightly closed. Dry.
Change contaminated clothing. Wash hands after working with substance.
Keep away from open flames, hot surfaces and sources of ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Full contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:KCL 741 Dermatril® L Splash contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:KCL 741 Dermatril® L
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Respiratory protection is not required. Where protection from nuisance levels of dusts are desired, use type N95 (US) or type P1 (EN 143) dust masks. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or EN 14387 (EU).
protective clothing
No special precautionary measures necessary.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
No data available
No data available
no information available
Strong acids
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
12.2 Persistence and degradability
The methods for determining biodegradability are not applicable to inorganic substances.
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
The substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
12.6 Endocrine disrupting properties
The substance/mixture does not contain components considered to have endocrine disrupting properties at levels of 0.1% or higher.
12.7 Other adverse effects
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
No data available
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 718467
- Shipping Name
- Not dangerous goods
Regulatory Information
Chemical regulations, safety assessments, and compliance status
This material safety data sheet complies with the requirements of Regulation (EC) No. 1907/2006.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Titanium(IV) oxide?
The signal word is no signal word.
What is the physical form of Titanium(IV) oxide?
Titanium(IV) oxide is a nano particles with white color. It has no data available odor.
What is Titanium(IV) oxide used for?
Laboratory chemicals, Manufacture of substances
What is the melting point of Titanium(IV) oxide?
The melting point is 1.850 °C and the boiling point is No data available.