Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Buffer Solution, pH 7.00
- Product Code
- 63056125, 63056122, 63056116
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
professional, scientific and technical activities: other professional, scientific and technical activities
Uses advised against
None known.
Manufacturers & Suppliers
GFS Chemicals, Inc.
manufacturer
800 Kaderly Drive, Columbus, OH 43228
Mettler Toledo
distributor
1900 Polaris Parkway, Columbus, OH 43240
1-800-METTLER, 1-800-638-8537
http://www.mt.com/pH
Emergency Contacts
Chemtrec
800-424-9300
Chemtrec
1-703-741-5970
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. Call a physician if symptoms develop or persist.
Wash off with soap and water. Get medical attention if irritation develops and persists.
Rinse with water. Get medical attention if irritation develops and persists.
Symptoms: Direct contact with eyes may cause temporary irritation.
Rinse mouth. Get medical attention if symptoms occur.
Immediate Medical Attention
Treat symptomatically.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing agent suitable for type of surrounding fire.
Do not use water jet as an extinguisher, as this will spread the fire.
None known.
Move containers from fire area if you can do so without risk.
Firefighter Protection
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unnecessary personnel away.
Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Dilute with water. Flush to sewer if local regulations permit. Following product recovery, flush area with water.
Avoid discharge into drains, water courses or onto the ground.
Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Materials: absorbent material (e.g. cloth, fleece)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Observe good industrial hygiene practices.
Store in tightly closed container. Store away from incompatible materials (see Section 10 of the SDS). Keep containers tightly closed.
Observe good industrial hygiene practices.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Good general ventilation should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.
Wear appropriate chemical resistant gloves.
Wear safety glasses with side shields (or goggles).
In case of insufficient ventilation, wear suitable respiratory equipment.
Wear suitable protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Material is stable under normal conditions.
The product is stable and non-reactive under normal conditions of use, storage and transport.
Hazardous polymerization does not occur.
None known. Contact with incompatible materials.
None known.
No hazardous decomposition products are known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Collect and reclaim or dispose in sealed containers at licensed waste disposal site.
Dispose of in accordance with local regulations. This material and its container must be disposed of in a safe manner.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
This product is not known to be a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Buffer Solution, pH 7.00?
The signal word is no signal word.
What is the physical form of Buffer Solution, pH 7.00?
Buffer Solution, pH 7.00 is a liquid. appearing as clear. with yellow. color. It has odorless. odor.
What is Buffer Solution, pH 7.00 used for?
professional, scientific and technical activities: other professional, scientific and technical activities
What are the hazard statements for Buffer Solution, pH 7.00?
This substance has 1 hazard statement:
- The mixture does not meet the criteria for classification.
What is the melting point of Buffer Solution, pH 7.00?
The melting point is 32 °F (0 °C) estimated and the boiling point is 212 °F (100 °C) estimated.