Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Tissue-Tek® O.C.T. Compound
- Product Code
- 4583
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Tissue-Tek® Cryo instruments
Uses advised against
None known.
Manufacturers & Suppliers
Sakura Finetek USA Inc.
manufacturer
1750 West 214th St. Torrance, CA 90501
1-310-972-7800
Emergency Contacts
CHEMTREC
1-800-424-9300
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Polyvinyl alcohol | 9002-89-5 | 5 - 15% | No |
| Polyethylene glycol | 25322-68-3 | 1 - 10% | No |
| Non-reactive ingredient | --- | 75 - 95% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. Call a physician if symptoms develop or persist.
Symptoms: symptoms develop or persist
Wash off with soap and water. Get medical attention if irritation develops and persists.
Symptoms: irritation develops and persists
Rinse with water. Get medical attention if irritation develops and persists.
Symptoms: Direct contact with eyes may cause temporary irritation. Irritation develops and persists.
Rinse mouth. Get medical attention if symptoms occur.
Symptoms: symptoms occur
Immediate Medical Attention
Treat symptomatically.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Powder. Alcohol resistant foam. Carbon dioxide (CO2).
None known.
During fire, gases hazardous to health may be formed.
Move containers from fire area if you can do so without risk. Use standard firefighting procedures and consider the hazards of other involved materials.
Firefighter Protection
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unnecessary personnel away.
Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.
Never return spills to original containers for re-use. Avoid discharge into drains, water courses or onto the ground.
Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Materials: vermiculite, dry sand or earth, absorbent material (e.g. cloth, fleece)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with skin, eyes and clothing. Avoid breathing mist. Observe good industrial hygiene practices.
Store in original tightly closed container. Store in a cool and well-ventilated place.
Observe good industrial hygiene practices.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
General ventilation normally adequate.
Wear appropriate chemical resistant gloves. Suitable gloves can be recommended by the glove supplier.
Not normally needed. Risk of contact: Wear safety glasses with side shields (or goggles).
Not normally needed. When engineering controls are not sufficient to lower exposure levels below the applicable exposure limit, use a NIOSH approved respirator.
Wear suitable protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
The product is not classified as environmentally hazardous, though large or frequent spills may have harmful effects.
Persistence and degradability
No data is available on the degradability of this product.
Bioaccumulative potential
No data available.
Mobility in soil
The product is water soluble and may disperse in soil.
Other adverse effects
No other adverse environmental effects are expected from this component.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
This product is not known to be a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Tissue-Tek® O.C.T. Compound?
The signal word is no signal word.
What is the physical form of Tissue-Tek® O.C.T. Compound?
Tissue-Tek® O.C.T. Compound is a liquid. appearing as clear, viscous liquid. with colorless to pale yellow. color. It has slight alcohol. odor.
What is the solubility of Tissue-Tek® O.C.T. Compound?
Soluble
What is Tissue-Tek® O.C.T. Compound used for?
Tissue-Tek® Cryo instruments
What is the melting point of Tissue-Tek® O.C.T. Compound?
The melting point is Not available. and the boiling point is Not available..