Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
Shell Tonna S3 M 68 is a liquid at room temperature. substance commonly used machine oil..
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
GHS Hazard Pictograms & Safety Symbols
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
Precautionary Statements
Manufacturers & Suppliers
Authorized suppliers, manufacturers, and distribution network information
Viva Energy Australia Pty Ltd
national supplier
720 Bourke Street Docklands Victoria 3008 Australia
AU
+61 (0)3 8823 4444
+61 (0)3 8823 4800
24/7 Emergency Response
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
Emergency Contact
1800 651 818
AU
POISONS INFORMATION CENTRE
13 11 26
AU
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
mixtureGeneral Composition
Highly refined mineral oils and additives.
Chemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Interchangeable low viscosity base oil (<20,5 cSt @40C) | N/A | 90% | Hazardous |
| Alkyl thiadiazole EC: 236-912-2 | 13539-13-4 | Not specified | Hazardous |
Additional Information
contains one or more of the following CAS-numbers: 6474253-6, 64742-54-7, 64742-55-8, 64742-56-9, 64742-65-0, 68037-01-4, 72623-86-0, 72623-87-1, 8042-47-5, 848301-699.
Composition Notes
The highly refined mineral oil contains <3% (w/w) DMSOextract, according to IP346.
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
Inhalation Exposure
No treatment necessary under normal conditions of use.
Skin Contact
Remove contaminated clothing. Flush exposed area with water and follow by washing with soap if available.
Eye Contact
Flush eye with copious quantities of water. Remove contact lenses, if present and easy to do. Continue rinsing.
Ingestion/Swallowing
In general no treatment is necessary unless large quantities are swallowed.
Symptoms:
Ingestion may result in nausea, vomiting and/or diarrhoea.
Immediate Medical Attention Required
If symptoms persist, obtain medical advice. If persistent irritation occurs, obtain medical attention. If large quantities are swallowed, get medical advice.
Medical Treatment
Treat symptomatically.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Exposure Controls & Personal Protective Equipment
Occupational exposure limits, engineering controls, and required safety equipment
Engineering Controls
The level of protection and types of controls necessary will vary depending upon potential exposure conditions. Select controls based on a risk assessment of local circumstances. Appropriate measures include: Adequate ventilation to control airborne concentrations. Where material is heated, sprayed or mist formed, there is greater potential for airborne concentrations to be generated.
Hand Protection
Where hand contact with the product may occur the use of gloves approved to relevant standards (e.g. Europe: EN374, US: F739) made from the following materials may provide suitable chemical protection. PVC, neoprene or nitrile rubber gloves Suitability and durability of a glove is dependent on usage, e.g. frequency and duration of contact, chemical resistance of glove material, dexterity. Always seek advice from glove suppliers. Contaminated gloves should be replaced. Personal hygiene is a key element of effective hand care. Gloves must only be worn on clean hands. After using gloves, hands should be washed and dried thoroughly. Application of a non-perfumed moisturizer is recommended. For continuous contact we recommend gloves with breakthrough time of more than 240 minutes with preference for > 480 minutes where suitable gloves can be identified. For short-term/splash protection we recommend the same but recognize that suitable gloves offering this level of protection may not be available and in this case a lower breakthrough time maybe acceptable so long as appropriate maintenance and replacement regimes are followed. Glove thickness is not a good predictor of glove resistance to a chemical as it is dependent on the exact composition of the glove material. Glove thickness should be typically greater than 0.35 mm depending on the glove make and model.
Eye Protection
If material is handled such that it could be splashed into eyes, protective eyewear is recommended.
Respiratory Protection
No respiratory protection is ordinarily required under normal conditions of use. In accordance with good industrial hygiene practices, precautions should be taken to avoid breathing of material. If engineering controls do not maintain airborne concentrations to a level which is adequate to protect worker health, select respiratory protection equipment suitable for the specific conditions of use and meeting relevant legislation. Check with respiratory protective equipment suppliers. Where air-filtering respirators are suitable, select an appropriate combination of mask and filter. Select a filter suitable for the combination of organic gases and vapours and particles [Type A/Type P boiling point >65C (149F)].
Skin/Body Protection
Skin protection is not ordinarily required beyond standard work clothes. It is good practice to wear chemical resistant gloves.
Environmental Exposure Controls
Take appropriate measures to fulfill the requirements of relevant environmental protection legislation. Avoid contamination of the environment by following advice given in Section 6. If necessary, prevent undissolved material from being discharged to waste water. Waste water should be treated in a municipal or industrial waste water treatment plant before discharge to surface water. Local guidelines on emission limits for volatile substances must be observed for the discharge of exhaust air containing vapour.
Transportation & Shipping Information
UN numbers, shipping names, transport classes, and regulatory transport requirements
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for Shell Tonna S3 M 68?
The signal word for this substance is "no signal word".
What is the physical form of Shell Tonna S3 M 68?
Shell Tonna S3 M 68 is a liquid at room temperature. appearing as liquid at room temperature. with light brown color. It has slight hydrocarbon odor.
What is Shell Tonna S3 M 68 used for?
Machine oil.
What is the melting point of Shell Tonna S3 M 68?
The melting point is Data not available and the boiling point is > 280 C / 536 Festimated value(s).