Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MASTER ALLOY ALUMINIUM-BERYLLIUM
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
alloying and desoxidising of Al and Mg
Manufacturers & Suppliers
TROPAG, Oscar H.Ritter Nachf. GmbH
Bundesstr. 4, D-20146 Hamburg
+49 (0)40 41 40 13-0
Emergency Contacts
Toxic Substance Emergency Call Center North
+49 (0)551 19240
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove affected person from the immediate area. Ensure supply of fresh air. Irregular breathing/no breathing: artificial respiration. Summon a doctor immediately.
Wash off immediately with soap and water.
Separate eyelids, wash the eyes thoroughly with water (15 min.). Eye treatment by an oculist.
Rinse out mouth and give plenty of water to drink. Summon a doctor immediately. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Summon a doctor immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Adapt extinguisher and fire-fighting measures to fire in the environment.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Refer to protective measures listed in sections 7 and 8.
Do not discharge into the drains/surface waters/groundwater.
Pick up mechanically.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Provide good ventilation of working area. If workplace exposure limits are exceeded, respiratory protection approved for this particular job must be worn.
Store product in closed containers. Keep container dry in a cool, well-ventilated place.
No special measures necessary.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Sufficient protection is given wearing suitable protective gloves checked according to i.e. EN 374, in the event of risk of skin contact with the product. Before use, the protective glove should be tested in any case for its specific work-station suitability (i.e. mechanical resistance, product compatibility and antistatic properties). Adhere to the manufacturer's instructions and information relating to the use, storage, care and replacement of protective gloves. Protective gloves shall be replaced immediately when physically damaged or worn. Design operations thus to avoid permanent use of protective gloves.
Safety glasses (EN 166)
If workplace exposure limits are exceeded, a respiration protection approved for this particular job must be worn.
Clothing as usual in the chemical industry.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used as prescribed.
Acids; Alcalis
Formation of hydrogen in contact with acids.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Allocation of a waste code number, according to the European Waste Catalogue, should be carried out in agreement with the regional waste disposal company.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
In the form in which it is marketed, the product causes no danger to health for humans through inhalation, swallowing or contact with the skin. There is therefore no obligation to classify/label the product in accordance with appendix VI, no. 9.3, EC Directive 67/548/EEC.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MASTER ALLOY ALUMINIUM-BERYLLIUM?
The signal word is no signal word.
What is the physical form of MASTER ALLOY ALUMINIUM-BERYLLIUM?
MASTER ALLOY ALUMINIUM-BERYLLIUM is a solid with silver-grey color.
What is MASTER ALLOY ALUMINIUM-BERYLLIUM used for?
alloying and desoxidising of Al and Mg
What is the melting point of MASTER ALLOY ALUMINIUM-BERYLLIUM?
The melting point is 800 °C .