Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Isooctane ASTM
- Product Code
- 205484
Regulatory Identifiers
- CAS Number
- 540-84-1 Check regulations →
- EC Number
- 208-759-1 Check regulations →
- REACH No.
- 01-2119457965-22-0001
Identified Uses
Manufacture of substance - Industrial, Distribution of substance - Industrial, Formulation and (re)packaging of substances and mixtures - Industrial, Use in Coatings - Industrial, Use in Coatings - Professional, Use in Coatings - Consumer, Use in Cleaning Agents - Industrial, Use in Cleaning Agents - Professional, Use in Cleaning Agents - Consumer, Use as a Fuel - Industrial, Use as a Fuel - Professional, Use as a Fuel - Consumer, Use in Laboratories - Industrial, Use in Laboratories - Professional
Manufacturers & Suppliers
Haltermann Carless Deutschland GmbH
manufacturer
Schlengendeich 17, 21107 Hamburg, Germany
+49 (0)40 333 18 0
Emergency Contacts
CHEMTREC
+1-703-527-3887
CHEMTREC (EMEA)
+44 20 3885 0382
CHEMTREC (UK)
+44 20 3807 3798
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
GHS08
GHS09
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2,2,4-trimethylpentane EC: 208-759-1 | 540-84-1 | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of unconsciousness bring patient into stable side position for transport.
Instantly wash with water and soap and rinse thoroughly. Instantly rinse with water.
Rinse opened eye for several minutes under running water.
Do not induce vomiting; instantly call for medical help.
Immediate Medical Attention
No further relevant information available.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, extinguishing powder or water spray. Fight larger fires with water spray or alcohol-resistant foam.
The vapour is heavier than air, spreads along the ground and ignition at a greater distance is possible.
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away.
Do not allow product to reach sewage system or water bodies. Prevent material from reaching sewage system, holes and cellars.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep containers tightly sealed. Prevent formation of aerosols.
Store in cool, dry place in tightly closed containers.
Keep ignition sources away - Do not smoke. Protect against electrostatic charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see section 7.
Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation Material of gloves The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. Nitrile rubber, NBR - 0,38 mm Penetration time of glove material - 480 min (EN 374)
Tightly sealed safety glasses.
Ensure good ventilation. This can be achieved by using a local exhaustion or general exhaust system. If these measures are insufficient to keep the solvent vapour concentration below the workplace limit, wear an adequate respiratory protective device. Filter A.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
No further relevant information available regarding aquatic toxicity.
12.2 Persistence and degradability
No further relevant information available.
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
The substance is not considered to be PBT or vPvB.
12.6 Endocrine disrupting properties
The product does not contain substances with endocrine disrupting properties.
12.1 Toxicity
12.2 Persistence and degradability
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
12.6 Endocrine disrupting properties
12.7 Other adverse effects
Very toxic for fish
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1262
- Shipping Name
- OCTANES, ENVIRONMENTALLY HAZARDOUS
- Transport Class
- 3
- Packing Group
- II
Warning: Flammable liquids. Special marking (ADR/RID): Symbol (fish and tree)
Warning: Flammable liquids.
Warning: Flammable liquids.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Isooctane ASTM?
The signal word is danger.
What is the physical form of Isooctane ASTM?
Isooctane ASTM is a fluid with colourless color. It has nearly odourless odor.
What is Isooctane ASTM used for?
Manufacture of substance - Industrial, Distribution of substance - Industrial, Formulation and (re)packaging of substances and mixtures - Industrial, Use in Coatings - Industrial, Use in Coatings - Professional, Use in Coatings - Consumer, Use in Cleaning Agents - Industrial, Use in Cleaning Agents - Professional, Use in Cleaning Agents - Consumer, Use as a Fuel - Industrial, Use as a Fuel - Professional, Use as a Fuel - Consumer, Use in Laboratories - Industrial, Use in Laboratories - Professional
What are the hazard statements for Isooctane ASTM?
This substance has 5 hazard statements:
- H225: Highly flammable liquid and vapour.
- H304: May be fatal if swallowed and enters airways.
- H315: Causes skin irritation.
- H336: May cause drowsiness or dizziness.
- H410: Very toxic to aquatic life with long lasting effects.
What is the melting point of Isooctane ASTM?
The melting point is -107 C and the boiling point is 99 C.