Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BD FC Beads BV421
- Product Code
- 661627
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Reserved for industrial and professional use.
Uses advised against
Not for use in diagnostic or therapeutic procedures.
Manufacturers & Suppliers
Becton, Dickinson and Company - BD Biosciences
manufacturer
2350 Qume Drive, 95131 San Jose, CA
1 877 232 8995
Emergency Contacts
ChemTrec
1 800 424 9300
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2-Methyl-4-isothiazolin-3-one | 2682-20-4 | 0.8125% | No |
| Sodium azide (Na(N3)) | 26628-22-8 | 0.0624% | No |
Notes
* All concentrations are percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume.
First Aid Measures
Emergency procedures for chemical exposure incidents
Provide fresh air, warmth and rest, preferably in comfortable upright sitting position. Get medical attention if symptoms persist.
Wash off promptly and flush contaminated skin with water. Promptly remove clothing if soaked through and flush skin with water. Get medical attention if symptoms occur. Wash contaminated clothing before reuse.
Immediately flush with plenty of water for at least 15 minutes. If easy to do, remove contact lenses. Get medical attention promptly if symptoms occur after washing.
If swallowed, rinse mouth with water (only if the person is conscious). Do NOT induce vomiting. Get medical attention immediately.
Immediate Medical Attention
Get medical attention immediately. Get medical attention if symptoms persist. Get medical attention promptly if symptoms occur after washing. Get medical attention if symptoms occur.
Medical Treatment
Wash off promptly and flush contaminated skin with water. Promptly remove clothing if soaked through and flush skin with water.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray, fog, CO2, dry chemical, or alcohol resistant foam.
Avoid water in straight hose stream; will scatter and spread fire.
Fire or excessive heat may produce hazardous decomposition products.
No unusual fire or explosion hazards noted. Use water to keep fire exposed containers cool and disperse vapors.
Firefighter Protection
Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Ensure suitable personal protection (including respiratory protection) during removal of spillages in a confined area.
Avoid release to the environment. Run off may pollute waterways.
Absorb spillage with suitable absorbent material.
Materials: suitable absorbent material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wash promptly with soap and water if skin becomes contaminated. When using do not eat, drink or smoke. Read and follow manufacturer's recommendations. Use personal protective equipment as required.
Store in tightly closed original container in a dry, cool and well-ventilated place. Product performance to shelf life is dependent upon long term storage at 2-8°C
Wash promptly with soap and water if skin becomes contaminated. When using do not eat, drink or smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Adequate ventilation should be provided whenever the material is heated or mists are generated.
Use suitable protective gloves if risk of skin contact.
Wear safety glasses with side shields (or goggles).
If engineering controls do not maintain airborne concentrations below recommended exposure limits (where applicable) or to an acceptable level (in countries where exposure limits have not been established), an approved respirator must be worn.
Wear appropriate clothing to prevent repeated or prolonged skin contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No data available.
Stable under normal temperature conditions and recommended use.
None under normal conditions.
Avoid exposure to high temperatures or direct sunlight.
Strong oxidizing agents.
By heating and fire, harmful vapors/gases may be formed.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Discharge, treatment, or disposal may be subject to national, state, or local laws.
Dispose of waste and residues in accordance with local authority requirements.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BD FC Beads BV421?
The signal word is warning.
What is the physical form of BD FC Beads BV421?
BD FC Beads BV421 is a solid with colorless color. It has characteristic odor.
What is BD FC Beads BV421 used for?
Reserved for industrial and professional use.
What are the hazard statements for BD FC Beads BV421?
This substance has 2 hazard statements:
- H317: May cause an allergic skin reaction.
- H402: Harmful to aquatic life.
What is the melting point of BD FC Beads BV421?
The melting point is No data available. and the boiling point is No data available..