Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE 55
- Synonyms
- Loctite 55
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Adhesive
Manufacturers & Suppliers
Henkel Ltd
manufacturer
Wood Lane End, HP2 4RQ Hemel Hempstead, Great Britain
+44 1442 278000
Emergency Contacts
Emergency Contact
+44 (0)1442 278497
24 Hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Coated Nylon Thread
Notes
Contains no dangerous substances exceeding the limits of the EU-Regulation
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air, consult doctor if complaint persists.
Rinse with running water and soap. Obtain medical attention if irritation persists.
Symptoms: Prolonged or repeated contact may cause skin irritation.
Rinse immediately with plenty of running water, seek medical advice if necessary.
Symptoms: Prolonged or repeated contact may cause eye irritation.
Rinse mouth and throat. Drink 1-2 glasses of water. Seek medical advice.
Immediate Medical Attention
Obtain medical attention if irritation persists (skin), seek medical advice if necessary (eyes), seek medical advice (ingestion), consult doctor if complaint persists (inhalation).
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
carbon dioxide, foam, powder, water spray jet, fine water spray
High pressure waterjet
In the event of a fire, carbon monoxide (CO) and carbon dioxide (CO2) can be released.
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid contact with skin and eyes. Ensure adequate ventilation. Wear protective equipment.
Do not empty into drains / surface water / ground water.
Scrape up as much material as possible. Sweep up spilled material.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid skin and eye contact.
Store in a cool, dry place. Keep container tightly sealed.
Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working. Good industrial hygiene practices should be observed.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation.
Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) This information is based on literature references and on information provided by glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of chemical-resistant protective gloves may be considerably shorter than the permeation time determined in accordance with EN 374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should be replaced.
Safety glasses with sideshields or chemical safety goggles should be worn if there is a risk of splashing. Protective eye equipment should conform to EN166.
Ensure adequate ventilation. An approved mask or respirator fitted with an organic vapour cartridge should be worn if the product is used in a poorly ventilated area Filter type: A (EN 14387)
Wear suitable protective clothing. Protective clothing should conform to EN 14605 for liquid splashes or to EN 13982 for dusts.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
None if used for intended purpose.
See section reactivity
None if used for intended purpose.
None if used properly.
None known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of in accordance with local and national regulations.
Dispose of in accordance with local and national regulations.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What other names is LOCTITE 55 known by?
LOCTITE 55 is also known as: Loctite 55
What is the hazard signal word for LOCTITE 55?
The signal word is no signal word.
What is the physical form of LOCTITE 55?
LOCTITE 55 is a solid material, paste appearing as solid material, paste with white color. It has characteristic odor.
What is the solubility of LOCTITE 55?
Partially soluble
What is LOCTITE 55 used for?
Adhesive
What is the melting point of LOCTITE 55?
The melting point is No data available / Not applicable and the boiling point is 150 °C (302 °F).