NextSDS Logo
Safety Data Sheet EN

innovatek Protect IP 25 % - Application mixture

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
innovatek Protect IP 25 % - Application mixture

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Corrosion protection

Uses advised against

No information on this is available at present.

Manufacturers & Suppliers

Innovatek OS GmbH logo

Innovatek OS GmbH

manufacturer

Stadtweg 9, 85134 Stammham

+49 8405 9259-0

https://www.innovatek.de

Emergency Contacts

Giftinformationszentrum-Nord der Länder Bremen, Hamburg, Niedersachsen und Schleswig-Holstein (GIZ-Nord), Universitätsmedizin Göttingen - Georg-August-Universität

+49 551 19240

24 Stunden am Tag

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Acute Tox. Cat. 4 H302
STOT RE Cat. 2 H373

GHS Pictograms

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H302 Harmful if swallowed
H373 May cause damage to organs through prolonged or repeated exposure (kidneys).

Precautionary Statements

P260 Do not breathe vapour or aerosol.
P264 Wash thoroughly with plenty of soap and water after use.
P270 Do not eat, drink or smoke when using.
P301 + P330 If swallowed: Rinse out mouth.
P312 If you feel unwell: Call poison control center or doctor.
P501 Dispose of contents/container to hazardous or special waste collection point.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Ethanediol EC: 203-473-3 107-21-1 25% Yes
Disodium sebacate EC: 241-300-3 17265-14-4 0.25 - 1.25% Yes

Notes

Text of H-phrases and classification abbreviations (GHS/CLP) see section 16. The substances mentioned in this section are listed with their actual, applicable classification! This means that for substances listed in Table 3.1 of Annex VI to Regulation (EC) No. 1272/2008 (CLP Regulation), all notes possibly mentioned there have been taken into account for the classification mentioned here.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person from danger zone. Supply person with fresh air and consult doctor depending on symptoms.

Skin contact

Wash thoroughly with plenty of soap and water, remove contaminated, soaked clothing immediately, in case of skin irritation (redness etc.), consult a physician.

Symptoms: skin irritation (redness etc.)

Eye contact

Remove contact lenses. Rinse thoroughly with plenty of water for several minutes, if necessary consult a doctor.

Ingestion

Rinse mouth thoroughly with water. Give plenty of water to drink, seek medical attention immediately. Make drink approx. 100 ml of approx. 25 % ethanol in pourable form.

Immediate Medical Attention

seek medical attention immediately

Medical Treatment

Symptomatic treatment (decontamination, elemental aid)

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray; Extinguishing powder; Alcohol resistant foam; Carbon dioxide (CO2)

Unsuitable media

None known

Specific hazards

In the event of fire, the following may be formed: Carbon oxides

Instructions

Do not inhale explosion and fire gases. Depending on fire size, use full protection if necessary. Cool endangered containers with water.

Firefighter Protection

Personal protective equipment see section 8. Depending on fire size, use full protection if necessary.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

In case of spillage or accidental release, to prevent contamination, wear personal protective equipment specified in section 8. Ensure adequate ventilation, remove sources of ignition. In case of solid or powdery products, avoid dust formation. If possible leave the danger zone, use existing emergency plans if necessary. Keep unprotected persons away. Ensure sufficient ventilation. Avoid contact with eyes and skin. If necessary, observe the risk of slipping.

Large spill

Pump off product.

Environmental

Do not allow to enter sewage system. Prevent from entering surface and ground water as well as soil.

Cleanup methods

Absorb with liquid-binding material (e.g. universal binder, sand, diatomaceous earth, sawdust) and dispose of according to section 13.

Materials: liquid-binding material (e.g. universal binder, sand, diatomaceous earth, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Ensure sufficient ventilation. Avoid contact with eyes and skin. Do not eat, drink, smoke or store food in the work area. Observe the information on the label and the instructions for use. Use working procedures according to operating instructions. Caution: danger of slipping. Do not inhale vapor / aerosol.

Storage

Store out of reach of unauthorized persons. Store product only in original packaging and closed. Do not store product in passageways and stairways. Store at room temperature. Avoid exposure to humidity and water. Keep containers tightly closed. Store in a dry place.

Hygiene

Wash hands before breaks and at the end of work. Keep away from food, beverages and feed. Remove contaminated clothing and protective equipment before entering areas where food is consumed.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Ensure good ventilation. This can be achieved by local exhaust ventilation or general exhaust air. If this is not sufficient to keep the concentration below the occupational exposure limits (OEL), suitable respiratory protection must be worn.

Hands

Chemical resistant protective gloves (EN ISO 374). Recommended: Protective gloves made of nitrile (EN ISO 374). Minimum layer thickness in mm: 0.4. Permeation time (breakthrough time) in minutes: >= 480. The determined breakthrough times according to EN 16523-1 were not carried out under practical conditions. A maximum wearing time corresponding to 50% of the breakthrough time is recommended. Hand protection cream recommended.

Eyes

Safety glasses tight fitting with side shields (EN 166).

Respiratory

If the occupational exposure limit value (AGW, Germany) or MAK (Switzerland, Austria) is exceeded. Filter A P2 (EN 14387), identification color brown, white. Observe wearing time limitations for respirators.

Skin/Body

Protective work clothing (e.g. safety shoes EN ISO 20345, long-sleeved work clothing).

Environmental

No information on this is available at present.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Decomposition Temperature
No information available on this parameter.
Form
---
Vapor Pressure
0.2 hPa (20°C)
Melting Point
≤ -12 °C
Bulk Density
---
Auto Ignition Temperature
---
Properties Status
---
Voc Content
---
Solidification Point
---
Physical State
Liquid
Colour
Colorless
Solubility
Polar solvents
Upper Explosive Limit
15 Vol-% (20 °C)
Boiling Point
> 103 °C
Ph
7 - 9 (20 °C, ASTM D 1287)
Solubility In Fat
---
Evaporation Rate
---
Explosive Limits
---
Relative Evaporation Rate
---
Dynamic Viscosity
---
Crystallisation Point
---
Odor
Almost odorless
Vapor Density
---
Cloud Point
---
Relative Density
---
Odor Threshold
---
State Under Standard Conditions
---
Softening Point
---
Density
1.04 g/cm3 (20°C, DIN 51757)
Partition Coefficient
Not applicable to mixtures.
Appearance
---
Solubility In Water
Miscible
Freezing Point
≤ -12 °C
Metal Corrosion
---
Kinematic Viscosity
3 - 5mm2/s (20 °C, DIN 51562)
Physical State Data
liquid
Flash Point
> 110 °C
Lower Explosive Limit
3.2 vol-% (20 °C)
Flammability
Not applicable.
Colour Intensity
---
Molecular Weight
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable when properly stored and handled

Reactivity

No hazardous reactions if the regulations/instructions for storage and handling are observed. Metal corrosion: Does not corrode metals.

Hazardous reactions

No dangerous reactions known.

Avoid

None known.

Incompatible

Avoid contact with strong oxidizing agents.

Decomposition

No decomposition when used as intended

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Treatment

Disposal via wastewater is not recommended. Observe local official regulations. For example, suitable incineration plant. For example, dispose of at a suitable landfill site.

Disposal

Disposal via wastewater is not recommended. Observe local official regulations. For example, suitable incineration plant. For example, dispose of at a suitable landfill site.

Waste Codes

16 01 14 Antifreeze containing dangerous substances EWC
14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
Not applicable
Transport Class
Not applicable / Not dangerous goods
Packing Group
Not applicable
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

Chemical Safety Assessment Not performed
?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for innovatek Protect IP 25 % - Application mixture?

The signal word is warning.

What is the physical form of innovatek Protect IP 25 % - Application mixture?

innovatek Protect IP 25 % - Application mixture is a liquid with colorless color. It has almost odorless odor.

What is the solubility of innovatek Protect IP 25 % - Application mixture?

Polar solvents

What is innovatek Protect IP 25 % - Application mixture used for?

Corrosion protection

What are the hazard statements for innovatek Protect IP 25 % - Application mixture?

This substance has 2 hazard statements:

  • H302: Harmful if swallowed
  • H373: May cause damage to organs through prolonged or repeated exposure (kidneys).

What is the melting point of innovatek Protect IP 25 % - Application mixture?

The melting point is ≤ -12 °C and the boiling point is > 103 °C.