RAVASOL TERGE CAH50

Take the victim into open air; keep them warm and calm. If breathing is irregular or stops, perform artificial respiration.

Symptoms: inhalation can cause internal damage

Remove contaminated clothing. Wash skin vigorously with water and soap or a suitable skin cleaner. NEVER use solvents or thinners.

Symptoms: contact with skin can cause burns

Wash eyes with plenty of clean and cool water for at least 10 minutes while pulling eyelids up, and seek medical assistance. Dont let the person to rub the affected eye.

Symptoms: Contact with eyes may cause irreversible damage. Contact with eyes can cause burns.

If accidentally ingested, seek immediate medical attention. Keep calm. NEVER induce vomiting.

Symptoms: ingestion can cause internal damage

Extinguisher powder or CO2. In case of more serious fires, also alcohol-resistant foam and water spray.

Do not use a direct stream of water to extinguish. In the presence of electrical voltage, you cannot use water or foam as extinguishing media.

Exposure to combustion or decomposition products can be harmful to your health.

Use water to cool tanks, cisterns, or containers close to the heat source or fire. Take wind direction into account.

In case of large spills, inform the responsible authorities according to local legislation.

Product dangerous for the environment, in case of large spills or if the product contaminates lakes, rivers, or sewers, inform the responsible authorities according to local legislation. Prevent the contamination of drains, surface or subterranean waters, and the ground.

Clean the area immediately with a suitable decontaminant.

Materials: inert absorbent material (earth, sand, vermiculite, Kieselguhr...)

In the application area, smoking, eating, and drinking must be prohibited. Follow legislation on occupational health and safety. Never use pressure to empty the containers. They are not pressure-resistant containers. Keep the product in containers made of a material identical to the original.

Store according to local legislation. Observe indications on the label. Store the containers between 5 and 25 °C, in a dry and well-ventilated place, far from sources of heat and direct solar light. Keep far away from ignition points. Keep away from oxidising agents and from highly acidic or alkaline materials. Do not smoke. Prevent the entry of non-authorised persons. Once the containers are open, they must be carefully closed and placed vertically to prevent spills.

In the application area, smoking, eating, and drinking must be prohibited.

Keep far away from ignition points. Do not smoke.

Provide adequate ventilation, which can be achieved by using good local exhaust-ventilation and a good general exhaust system.

PPE: Work gloves. Characteristics: «CE» marking, category I. CEN standards: EN 374-1, En 374-2, EN 374-3, EN 420. Maintenance: Keep in a dry place, away from any sources of heat, and avoid exposure to sunlight as much as possible. Do not make any changes to the gloves that may alter their resistance, or apply paints, solvents or adhesives. Observations: Gloves should be of the appropriate size and fit the user's hand well, not being too loose or too tight. Always use with clean, dry hands. Material: PVC (polyvinyl chloride) (Breakthrough time: > 480 min., Thickness: 0,35 mm); Butyl (Breakthrough time: > 480 min., Thickness: 0,3 mm); Nitrile (Breakthrough time: > 30 min., Thickness: 0,4 mm); Neoprene (Breakthrough time: > 30 min., Thickness: 0,5 mm).

PPE: Protective goggles with built-in frame. Characteristics: «CE» marking, category II. Eye protector with built-in frame for protection against dust, smoke, fog and vapour. CEN standards: EN 165, EN 166, EN 167, EN 168. Maintenance: Visibility through lenses should be ideal. Therefore, these parts should be cleaned daily. Protectors should be disinfected periodically following the manufacturer's instructions. Observations: Some signs of wear and tear include: yellow colouring of the lenses, superficial scratching of the lenses, scraping etc.

PPE: Filter mask for protection against gases and particles. Characteristics: «CE» marking, category III. The mask must have a wide field of vision and an anatomically designed form in order to be sealed and watertight. CEN standards: EN 136, EN 140, EN 405. Maintenance: Should not be stored in places exposed to high temperatures and damp environments before use. Special attention should be paid to the state of the inhalation and exhalation valves in the face adaptor. Observations: Read carefully the manufacturer's instructions regarding the equipment's use and maintenance. Attach the necessary filters to the equipment according to the specific nature of the risk (Particles and aerosols: P1-P2-P3, Gases and vapours: A-B-E-K-AX), changing them as advised by the manufacturer. Filter Type needed: A2.

PPE: Protective clothing. Characteristics: «CE» marking, category II. Protective clothing should not be too tight or loose in order not to obstruct the user's movements. CEN standards: EN 340. Maintenance: In order to guarantee uniform protection, follow the washing and maintenance instructions provided by the manufacturer. Observations: The protective clothing should offer a level of comfort in line with the level of protection provided in terms of the hazard against which it protects, bearing in mind environmental conditions, the user's level of activity and the expected time of use. PPE: Work footwear. Characteristics: «CE» marking, category II. CEN standards: EN ISO 13287, EN 20347. Maintenance: This product adapts to the first user's foot shape. That is why, as well as for hygienic reasons, it should not be used by other people. Observations: Work footwear for professional use includes protection elements aimed at protecting users against any injury resulting from an accident.

Stable under the recommended handling and storage conditions (see section 7).

The product does not present hazards by their reactivity.

The product does not present possibility of hazardous reactions.

Avoid any improper handling.

Keep away from oxidising agents and from highly alkaline or acidic materials in order to prevent exothermic reactions.

No decomposition if used for the intended uses.