ACMOS 81-400WE

Move to fresh air. Consult a physician if necessary

Wash off with soap and water. Preventive skin protection. In the case of skin irritation or allergic reactions see a physician.

Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician. If eye irritation persists, consult a specialist.

Do not induce vomiting. Consult a physician. Never give anything by mouth to an unconscious person.

Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. water, water spray, sand, alcohol-resistant foam, dry chemical, carbon dioxide (CO2)

None known

No special precautions required. The product itself does not burn.

Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Take up mechanically and collect in suitable container for disposal.

Dam up. Shovel into suitable container for disposal. Local authorities should be advised if significant spillages cannot be contained.

Do not flush into surface water or sanitary sewer system.

Dam up. Shovel into suitable container for disposal. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Take up mechanically and collect in suitable container for disposal.

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Use only in well-ventilated areas. When using, do not eat, drink or smoke.

Keep container tightly closed in a dry and well-ventilated place. Store at room temperature in the original container. Do not store outside. Avoid heating and direct sunlight.

When using, do not eat, drink or smoke.

Fire-fighting equipment on the basis of class B.

Design of appropriate work processes and engineering controls and the use of adequate materials (model solutions as certified working methods, working appliance according to the state of the art, optimization of process / spray robots, working appliance for prevention of skin contact, models of working times). Provide appropriate exhaust ventilation at machinery. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction.

Use only chemical protective gloves with CE-status of category III in accordance to EN 374. Suitable materials at long term, direct contact (Recommended : Preventive index 6, accordingly > 480 min. permeation time in accordance to EN 374) : Nitrile rubber / NBR (CAMATRIL VELOURS® - Art. No. 730) - Layer thickness : 0,4 mm. Suitable materials at short term contact or splash (Recommended : Preventive index 3, accordingly > 60 min. permeation time in accordance to EN 374) : Disposable gloves of special nitrile rubber / NBR (DERMATRIL® P - Art. No. 743) - Layer thickness : 0,2 mm. Decrease wearing protection gloves to an inevitable degree to avoid skin rash. Technical and organizational protective actions have to be preferred. Wear under gloves made of cotton as possible. Change preventive gloves once by hour or use special skin-protective preparations for protective gloves carrier, e.g. physioderm® proGlove Before removing gloves clean them with soap and water. Dispose preventive gloves after defect or expiry of wearing time. Check protective gloves to proper condition before usage.

safety glasses with side-shields (EN 166)

Breath protection at insufficient ventilation or prolonged exposition. Observe limited carrying time. The use of filter equipment requires a minimum oxygen content of 17 Vol-% in the surrounding atmosphere and that the maximum permitted gas concentration - normally 0,5 Vol-% - is not exceeded. Gas filtrating Half-face mask FFA (EN 405) Model 4251 (FFA1P1 - 1000 ml/m3) / 4255 (FFA2P2SL - 5000 ml/m3) - 3M, Internet : http://www.3m.com Half-face mask or Quarter-face mask with gas filter (EN 140) Filter type 6051 (A1 - 1000 ml/m3) / 6055 (A2 - 5000 ml/m3) - 3M, Internet : http://www.3m.com Full-face mask with gas filter (EN 136) Gas filter type : A, Indication colour : brown

Textile workclothing and shoes without special requirements. (EN 340)

Should not be released into the environment. Further information see under section 6.

Stable at normal conditions

none under normal use

none under normal use