Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- DESMODUR E 3265 MPA/SN
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Hardener for coating materials or adhesives for industrial and trade applications For details of the identified uses according to REACH-Regulation (EU) No. 1907/2006 refer to the annex of this safety data sheet.
Uses advised against
Not suitable for use in homeworker (DIY) applications.
Manufacturers & Suppliers
Bayer MaterialScience AG
manufacturer
BMS-IO-S&T-PSRA-PSI Product Safety 51368 Leverkusen
+49 214 30 25026
Emergency Contacts
Sicherheitszentrale Bayer
+49 214 30 99300
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| aliphatic polyisocyanate | 67892-85-7 | 65% | Yes |
| Solvent naphtha (petroleum), light arom. EC: 265-199-0 | 64742-95-6 | 29% | Yes |
| 2-methoxy-1-methylethyl acetate EC: 203-603-9 | 108-65-6 | 6% | Yes |
| Hexamethylene-1,6-diisocyanate | 822-06-0 | 0.26% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Take the person into the fresh air and keep him warm, let him rest; if there is difficulty in breathing, medical advice is required.
In case of skin contact wash affected areas thoroughly with soap and plenty of water. Consult a doctor in the event of a skin reaction.
Hold the eyes open and rinse with preferably lukewarm water for a sufficiently long period of time (at least 10 minutes). Contact an ophthalmologist.
DO NOT induce the patient to vomit, medical advice is required.
Medical Treatment
Basic first aid, decontamination, symptomatic treatment.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon dioxide (CO2), Foam, extinguishing powder, in cases of larger fires, water spray should be used.
High volume water jet
Burning releases carbon monoxide, carbon dioxide, oxides of nitrogen, isocyanate vapors and traces of hydrogen cyanide. In the event of fire and/or explosion do not breathe fumes.
Firefighter Protection
During fire-fighting respirator with independent air-supply and airtight garment is required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Put on protective equipment (see section 8). Keep away from sources of ignition. Ensure adequate ventilation/exhaust extraction. Keep unauthorized persons away.
Do not allow to escape into waterways, wastewater or soil.
After approx. one hour transfer to waste container and do not seal (evolution of CO2!). Keep damp in a safe ventilated area for several days.
Materials: wet, absorbent material (e.g. sawdust, chemical binder based on calcium silicate hydrate, sand)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The personal protective measures described in section 8 must be observed. The precautions required in the handling of solvents and isocyanates must be taken. Avoid contact with skin and eyes and the inhalation of vapor.
Keep container dry and tightly closed in a cool and well ventilated place.
Keep away from foodstuffs, drinks and tobacco. Wash hands before breaks and at end of work and use skin-protecting ointment. Keep working clothes separately. Take off all contaminated clothing immediately.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Conditionally suitable materials for protective gloves; EN 374: Butyl rubber - IIR: thickness >=0,5mm; breakthrough time >=60min. Recommendation: contaminated gloves should be disposed of.
Wear eye/face protection.
Respiratory protection required in insufficiently ventilated working areas and during spraying. An air-fed mask, or for short periods of work, a combination of charcoal filter and particulate filter is recommended. Further recommendations regarding respiratory protection can be found in the individual exposure scenarios in the appendix. In case of hypersensitivity of the respiratory tract and skin (e.g. asthmatics and those who suffer from chronic bronchitis and chronic skin complaint) it is inadvisable to work with the product.
Wear suitable protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
This information is not available.
This information is not available.
Exothermic reaction with amines and alcohols; reacts slowly with water forming CO2, in closed containers risk of bursting owing to increase of pressure.
This information is not available.
This information is not available.
No hazardous decomposition products when stored and handled correctly.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1866
- Shipping Name
- RESIN SOLUTION
- Transport Class
- 3
- Packing Group
- III
Special regulation for 'viscous substances' applicable
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for DESMODUR E 3265 MPA/SN?
The signal word is warning.
What is the physical form of DESMODUR E 3265 MPA/SN?
DESMODUR E 3265 MPA/SN is a liquid appearing as liquid with yellowish color. It has solvent-like odor.
What is DESMODUR E 3265 MPA/SN used for?
Hardener for coating materials or adhesives for industrial and trade applications For details of the identified uses according to REACH-Regulation (EU) No. 1907/2006 refer to the annex of this safety data sheet.
What are the hazard statements for DESMODUR E 3265 MPA/SN?
This substance has 5 hazard statements:
- H226: Flammable liquid and vapour.
- H317: May cause an allergic skin reaction.
- H332: Harmful if inhaled.
- H335: May cause respiratory irritation.
- H336: May cause drowsiness or dizziness.