Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Eastman Tetrashield(TM) MP2103
- Product Code
- 39667-00, P39667FJ, P39667FS, 50226031, P39667FE, P39667FT, P39667FH
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coatings
Uses advised against
None known.
Manufacturers & Suppliers
Eastman Chemical Company
manufacturer
200 South Wilcox Drive, 37660-5280 Kingsport
+14232292000
http://www.EASTMAN.com
Emergency Contacts
NCEC
+44 (0)1235 239 670
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
No hazardous ingredients
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove to fresh air. Treat symptomatically.
Wash off with soap and water.
In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
Seek medical advice.
Immediate Medical Attention
If symptoms persist, call a physician.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray, Carbon dioxide (CO2), Dry chemical
Do not use a solid water stream as it may scatter and spread fire.
Avoid generating dust; fine dust dispersed in air in sufficient fighting concentrations, and in the presence of an ignition source is a potential dust explosion hazard.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear appropriate personal protective equipment.
Avoid release to the environment.
Sweep up and shovel into suitable containers for disposal.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wash thoroughly after handling. Use only in area provided with appropriate exhaust ventilation. Minimize dust generation and accumulation.
Keep container tightly closed.
Handle in accordance with good industrial hygiene and safety practice.
Minimize dust generation and accumulation.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.
Wear suitable gloves.
Safety glasses
Use respiratory protection unless adequate local exhaust ventilation is provided or exposure assessment demonstrates that exposures are within recommended exposure guidelines. Wear respiratory protection when its use is identified for certain contributing scenario.
Wear suitable protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions.
None reasonably foreseeable.
Stable
Minimize dust generation and accumulation.
Strong oxidizing agents
Carbon monoxide Carbon dioxide (CO2)
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Eastman Tetrashield(TM) MP2103?
The signal word is no signal word.
What is the physical form of Eastman Tetrashield(TM) MP2103?
Eastman Tetrashield(TM) MP2103 is a pellets with light yellow color. It has no data available odor.
What is Eastman Tetrashield(TM) MP2103 used for?
Coatings
What is the melting point of Eastman Tetrashield(TM) MP2103?
The melting point is not determined and the boiling point is not determined.