Giemsa's azur eosin methylene blue solution for microscopy

Move to fresh air. Immediately call in physician. If breathing stops: immediately apply artificial respiration, if necessary also oxygen.

Take off immediately all contaminated clothing. Rinse skin with water/ shower. Call a physician immediately.

Rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses.

After swallowing: fresh air. Make victim drink ethanol (e.g. 1 drinking glass of a 40% alcoholic beverage). Call a doctor immediately (mention methanol ingestion). Only in exceptional cases, if no medical care is available within one hour, induce vomiting (only in fully conscious persons) and make victim drink ethanol again (approx. 0.3 ml of a 40% alcoholic beverage/kg body weight/hour).

Water, Foam, Carbon dioxide (CO2), Dry powder

For this substance/mixture no limitations of extinguishing agents are given.

Carbon oxides. Mixture with combustible ingredients. Fire may cause evolution of: Acrolein. Pay attention to flashback. Vapors are heavier than air and may spread along floors. Development of hazardous combustion gases or vapours possible in the event of fire. Forms explosive mixtures with air at ambient temperatures.

Remove container from danger zone and cool with water.

Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition. Evacuate the danger area, observe emergency procedures, consult an expert.

Do not let product enter drains. Risk of explosion.

Take up carefully with liquid-absorbent material (e.g. Chemizorb®). Clean up affected area.

Materials: liquid-absorbent material (e.g. Chemizorb®)

Work under hood. Do not inhale substance/mixture. Avoid generation of vapours/aerosols.

Keep container tightly closed in a dry and well-ventilated place. Keep away from heat and sources of ignition. Keep locked up or in an area accessible only to qualified or authorized persons. Recommended storage temperature see product label.

Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharge.

Full contact: Material: butyl-rubber, Minimum layer thickness: 0,7 mm, Break through time: 480 min, Material tested: Butoject® (KCL 898). Splash contact: Material: Viton®, Minimum layer thickness: 0,70 mm, Break through time: 120 min, Material tested: Vitoject® (KCL 890 / Aldrich Z677698, Size M). This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses

required when vapours/aerosols are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type ABEK. The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.

Flame retardant antistatic protective clothing.

Do not let product enter drains. Risk of explosion.

The product is chemically stable under standard ambient conditions (room temperature).

Vapors may form explosive mixture with air.

Risk of explosion with: Oxidizing agents, perchloric acid, perchlorates, salts of oxyhalogenic acids, chromium(VI) oxide, halogen oxides, nitrogen oxides, nonmetallic oxides, chromosulfuric acid, chlorates, hydrides, zinc diethyl, Halogens, Magnesium, hydrogen peroxide, Nitric acid, peroxi compounds, Nitriles. Exothermic reaction with: acid halides, Acid anhydrides, Reducing agents, Acids, Oxides of phosphorus. chromium(VI) oxide, phosphorus halides, Acetic anhydride with phosphorous oxichloride. Generates dangerous gases or fumes in contact with: Alkaline earth metals, Alkali metals. Risk of ignition or formation of inflammable gases or vapours with: potassium permanganate, calcium hypochlorite, Oxides of phosphorus, Fluorine. with Lead oxides: Generates dangerous gases or fumes in contact with: Alkaline earth metals, Alkali metals.

Warming.

various plastics, Aluminum, zinc alloys, Magnesium

In the event of fire: see section 5