Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Sulfur Oil Standard in Base Oil 20
- Product Code
- DSS8-1AY
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Certified Reference Material
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
SPEX CertiPrep, LLC
manufacturer
203 Norcross Ave, Metuchen, NJ 08840 USA
Emergency Contacts
CHEMTREC
800-424-9300
24 hours
CHEMTREC
703-527-3887
24 hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water.
If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
No further relevant information available.
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Not required.
No special measures required.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Sulfur Oil Standard in Base Oil 20
---
Sulfur Oil Standard in Base Oil 20
---
Base oil SAE 10/95
CAS: 64742-54-7
Endosulfan Sulfate Standard in Isooctane
---
Base Oil Ultra - S2 (60 Neutral)
---
Base oil BS 30/85
CAS: 101316-69-2
General Purpose Viscosity Standard – Synthetic Base Oil
---
HEAVY FUEL OIL (< 1% Sulfur)
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
No special requirements.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Additional information about design of technical systems: No further data; see item 7.
Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Goggles recommended during refilling.
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use respiratory protective device that is independent of circulating air.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known. No decomposition if used according to specifications.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Sulfur Oil Standard in Base Oil 20?
The signal word is warning.
What is the physical form of Sulfur Oil Standard in Base Oil 20?
Sulfur Oil Standard in Base Oil 20 is a liquid with according to product specification color. It has characteristic odor.
What is Sulfur Oil Standard in Base Oil 20 used for?
Certified Reference Material
What are the hazard statements for Sulfur Oil Standard in Base Oil 20?
This substance has 1 hazard statement:
- H317: May cause an allergic skin reaction.
What is the melting point of Sulfur Oil Standard in Base Oil 20?
The melting point is Undetermined. and the boiling point is Undetermined..