Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- OTTOSEAL M 361
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Sealant/ Adhesive
Uses advised against
Observe the information in the technical data sheet
Manufacturers & Suppliers
Hermann Otto GmbH
manufacturer
Krankenhausstraße 14, D-83413 Fridolfing
0049/(0)8684/908-0
Emergency Contacts
Carechem 24
+44 1865 407333
Emergency Contact
0049- (0) 89- 192 40
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Adhesive and sealant based on silane-terminated polymers (hybrid)
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| trimethoxyvinylsilane EC: 220-449-8 | 2768-02-7 | --- | Yes |
| N-(3-(trimethoxysilyl)propyl)ethylenediamine EC: 217-164-6 | 1760-24-3 | --- | Yes |
Particulate raw materials with risk of inhalation are inextricably bound in the product and therefore does not trigger classification of the product for inhalation hazards. Due to the product's physical properties, particulate inhalation exposure is not possible.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air. If required, provide artificial respiration. Keep patient warm.
Immediately wash with water and soap and rinse thoroughly. If skin irritation continues, consult a doctor.
Rinse opened eye for several minutes under running water. Then consult a doctor.
Do not induce vomiting; call for medical help immediately. Show container or label.
Immediate Medical Attention
Call for medical help immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Formation of toxic gases is possible during heating or in case of fire.
Do not inhale explosion gases or combustion gases.
Firefighter Protection
Mount respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not allow to enter sewers/ surface or ground water.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. see item 8: Personal protective equipment
Store in cool, dry conditions in well sealed receptacles. Protect from heat and direct sunlight.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see section 7.
Protective gloves. Recommended glove types: nitrile rubber. Recommended thickness of the material: >0.4 mm. Breakthrough time: 10 - 30 min. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer.
Safety glasses
This product should not be used under conditions of poor ventilation unless a protective mask with an appropriate gas filter (i.e. type ABEK according to standard EN 14387) is used.
Protective work clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
Contact with humidity, water and protic agents produces methanol.
Avoid strong heating.
No further relevant information available.
see item 5.2
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for OTTOSEAL M 361?
The signal word is no signal word.
What is the physical form of OTTOSEAL M 361?
OTTOSEAL M 361 is a liquid with according to product specification color. It has alcohol-like odor.
What is OTTOSEAL M 361 used for?
Sealant/ Adhesive
What is the melting point of OTTOSEAL M 361?
The melting point is undetermined and the boiling point is undetermined.