NextSDS Logo
Safety Data Sheet EN

LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY
Product Code
2983012

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Conductive Epoxy

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelina.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Eye Irrit. Cat. 2A
Skin Sens. Cat. 1
Muta. Cat. 2

GHS Pictograms

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H319 CAUSES SERIOUS EYE IRRITATION.
H341 SUSPECTED OF CAUSING GENETIC DEFECTS.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P261 Avoid breathing mist/vapours.
P264 Wash affected area thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

Hazardous Component(s) | CAS Number | Weight %*

Chemical Name CAS Number Concentration Hazardous
Silver 7440-22-4 60 - 80% Yes
4,4'-ethylidenediphenyl dicyanate 47073-92-7 10 - 30% Yes
2,2'-[[2-(oxiranylmethoxy)-1,3-phenylene]bis(methylene)]bisoxirane 13561-08-5 5 - 10% Yes
Formaldehyde, polymer with 2-(chloromethyl)oxirane and phenol, reaction products with propylenediamine 847257-79-8 1 - 5% Yes
Phenol-formaldehyde polymer 9003-35-4 1 - 5% Yes

Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.

Skin contact

Rinse with running water and soap. Remove contaminated clothing and shoes. If symptoms develop and persist, get medical attention. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Seek medical attention immediately.

Ingestion

Seek immediate medical attention. Do not induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Seek immediate medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.

Instructions

In case of fire, keep containers cool with water spray.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Isolate the hazard area and deny entry to unnecessary and unprotected personnel. Ensure adequate ventilation. Remove all sources of ignition. Keep unnecessary personnel away. Wear appropriate personal protective equipment. Refer to Section 8 'Exposure Controls / Personal Protection' prior to clean up. Evacuate and ventilate spill area; dike spill to prevent entry into water system; wear full protective equipment during clean-up.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wear suitable protective clothing, safety glasses and gloves. Keep container closed.

Storage

Keep container tightly closed and in a cool, well-ventilated place. Store in a dry place. Protect from direct sunlight.

Hygiene

Wash thoroughly after handling. When using do not eat, drink or smoke.

Fire prevention

Remove all sources of ignition. Keep away from heat, spark and flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Auto Ignition Temperature
Not available.
Lower Explosive Limit
Not available.
Physical State Data
liquid
Flammability
Not applicable
Cloud Point
---
Density
---
Odor
---
Relative Evaporation Rate
---
Odor Threshold
Not available.
Appearance
---
Melting Point
-53 °C (-63.4 °F)
Dynamic Viscosity
Not available.
Bulk Density
---
Physical State
liquid, paste
Flash Point
> 93.33 °C (> 199.99 °F)
Molecular Weight
---
Vapor Density
---
Softening Point
---
Ph
Not available.
Freezing Point
---
Properties Status
---
Colour Intensity
---
Voc Content
Not available.
Explosive Limits
---
Evaporation Rate
Not applicable
Vapor Pressure
Not applicable
Upper Explosive Limit
Not available.
Boiling Point
> 90 °C (> 194°F)
Form
---
Decomposition Temperature
Not available.
Crystallisation Point
---
Solubility
Negligible Water
Colour
Silver
Solubility In Water
---
Kinematic Viscosity
Not available.
Solubility In Fat
---
State Under Standard Conditions
---
Metal Corrosion
---
Solidification Point
---
Relative Density
3.5 (Water = 1)
Partition Coefficient
Not applicable
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. Protect from direct sunlight.

Incompatible

Strong oxidizing agents. Strong acids and strong bases. Amines.

Decomposition

Oxides of carbon. Oxides of Metals in Section 3. Toxic fumes. Irritating vapors. Phenolics.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3082
Shipping Name
RQ, Environmentally hazardous substance, liquid, n.o.s.
Transport Class
9
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY?

The signal word is warning.

What is the physical form of LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY?

LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY is a liquid, paste with silver color.

What is the solubility of LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY?

Negligible Water

What is LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY used for?

Conductive Epoxy

What are the hazard statements for LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY?

This substance has 3 hazard statements:

  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H319: CAUSES SERIOUS EYE IRRITATION.
  • H341: SUSPECTED OF CAUSING GENETIC DEFECTS.

What is the melting point of LOCTITE ABLESTIK XCE3111 2.7CC/10CC SY?

The melting point is -53 °C (-63.4 °F) and the boiling point is > 90 °C (> 194°F).