NextSDS Logo
Safety Data Sheet EN

BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING
Product Code
594596

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Special Products

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 3
Acute Tox. Cat. 3
Acute Tox. Cat. 2
Skin Corr. Cat. 1B
Eye Dam. Cat. 1
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
Muta. Cat. 1B
Carc. Cat. 1A
Repr. Cat. 1B
STOT RE Cat. 1

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS06 - Acute toxicity

GHS06

GHS08 - Serious health hazard

GHS08

Hazard Statements

H301 + H331 TOXIC IF SWALLOWED OR IF INHALED.
H310 FATAL IN CONTACT WITH SKIN.
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H340 MAY CAUSE GENETIC DEFECTS.
H350 MAY CAUSE CANCER.
H360 MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
H372 CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe vapors, mist, or spray.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P361 + P364 Take off immediately all contaminated clothing and wash it before reuse.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician. Rinse mouth.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Chromic acid 7738-94-5 1 - 5% Yes
Hydrogen fluoride 7664-39-3 1 - 5% Yes
Nitric acid 7697-37-2 1 - 5% Yes

IDH number: 594596 Product name: BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person immediately to fresh air. Seek medical attention if symptoms develop or persist. Administer oxygen or artificial respiration as needed. Trained personnel should administer 2.5% calcium gluconate through a nebulizer for 20 minutes. Do not use mouth-to-mouth method if victim ingested or inhaled the substance.

Symptoms: Delayed effects possible after inhalation.

Skin contact

Remove contaminated clothing and footwear while rinsing the affected area with large amounts of running water for at least 15 minutes. GET IMMEDIATE MEDICAL ATTENTION. If iced solution of 0.13% aqueous Benzalkonium Chloride (Zephiran) or 2.5% calcium gluconate gel is available, rinsing may be limited to 5 minutes, with the soak solution or gel applied as soon as the rinsing is stopped. If using calcium gluconate gel, it should be continuously re-applied and massaged into the affected area until pain has been relieved for at least 30 minutes. If Benzalkonium Chloride (Zephiran) or calcium gluconate gel is not available, rinsing must continue until medical treatment is provided. If symptoms develop and persist, get medical attention. Launder contaminated clothing before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Eye contact

Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Get immediate medical attention. Eye flushing should continue during transportation to a doctor.

Ingestion

Get immediate medical attention. Do not induce vomiting. If individual is conscious, wash out mouth with water. Provide a glass of water to dilute the material in the stomach. Attempt immediate administration of a fluoride binding substance: milk, chewable calcium carbonate tablets or 4-8 ounces (120-240 ml) of milk of magnesia or a liquid antacid. Avoid large amounts of liquid as it may induce vomiting. Never give anything by mouth to a victim who is unconscious or is having convulsions.

Immediate Medical Attention

GET IMMEDIATE MEDICAL ATTENTION.

Medical Treatment

Treatment of hypocalcemia associated with corrosive fluoride compounds exposure may be corrected by intravenous calcium gluconate or calcium chloride. Treatment of hypomagnesemia may be corrected by intravenous magnesium sulfate.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Wear appropriate personal protective equipment.

Cleanup methods

Absorb spill with inert material. Shovel material into appropriate container for disposal.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Avoid breathing mists or aerosols of this product. Wash thoroughly after handling. Use only with adequate ventilation. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material. Do not take internally. IN CASE OF CONTACT OR SUSPICION OF CONTACT, PROMPT MEDICAL ATTENTION IS ABSOLUTELY NECESSARY. For industrial use only.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Thaw and mix thoroughly if frozen.

Hygiene

Wash thoroughly after handling. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Relative Evaporation Rate
---
Colour
Dark orange
Kinematic Viscosity
Not available.
Odor
Pungent
Crystallisation Point
---
Density
---
Softening Point
---
Voc Content
Not applicable
Physical State Data
liquid
Upper Explosive Limit
Not applicable
Form
---
Cloud Point
---
Solubility In Water
---
Dynamic Viscosity
Not available.
Appearance
---
Molecular Weight
---
Melting Point
Not determined
Evaporation Rate
Not available.
Solidification Point
---
Ph
2.25
Boiling Point
> 100 °C (> 212°F) calculated
Flash Point
Not applicable
Physical State
Liquid
Decomposition Temperature
Not available.
Bulk Density
---
Vapor Density
---
Relative Density
1.04 - 1.06
Auto Ignition Temperature
Not applicable
Freezing Point
---
Colour Intensity
---
Explosive Limits
---
Vapor Pressure
Not determined
Flammability
Not applicable
Odor Threshold
Not available.
Solubility In Fat
---
Lower Explosive Limit
Not applicable
Partition Coefficient
Not determined
Metal Corrosion
---
State Under Standard Conditions
---
Solubility
Complete Water
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials.

Incompatible

This product may react with strong reducing agents. This product may react with strong acids, bases and oxidizing agents. This material will react with glass, concrete, certain metals, silica containing materials, rubber, leather, and many organics. Avoid contact with organic materials, oils, greases, and any oxidizable materials. Metals.

Decomposition

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. May liberate hydrogen fluoride. Chromium oxide.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
2922
Shipping Name
Corrosive liquids, toxic, n.o.s. (Hydrofluoric acid, Nitric acid)
Transport Class
8 (6.1)
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING?

The signal word is danger.

What is the physical form of BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING?

BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING is a liquid with dark orange color. It has pungent odor.

What is the solubility of BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING?

Complete Water

What is BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING used for?

Special Products

What are the hazard statements for BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING?

This substance has 9 hazard statements:

  • H301 + H331: TOXIC IF SWALLOWED OR IF INHALED.
  • H310: FATAL IN CONTACT WITH SKIN.
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H340: MAY CAUSE GENETIC DEFECTS.
  • H350: MAY CAUSE CANCER.
  • H360: MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
  • H372: CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of BONDERITE M-CR 713 CHROMATE COATING known as ALODINE 713 REPLENISHING?

The melting point is Not determined and the boiling point is > 100 °C (> 212°F) calculated.