Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TEROSON MS 9380 HPT BK FC570ML
- Product Code
- 2990488
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
adhesive and sealant
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Calcium carbonate | 471-34-1 | 30 - 60% | Yes |
| Silica, amorphous, fumed, cryst.-free | 112945-52-5 | 1 - 5% | Yes |
| Carbon black - Nano | 1333-86-4 | 1 - 5% | Yes |
IDH number: 2990488 Product name: TEROSON MS 9380 HPT BK FC570ML
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.
Wipe off with paper towel or cloth. Rinse with running water and soap. Remove contaminated clothing and shoes. Seek medical attention immediately. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Seek medical attention immediately.
DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Seek medical attention immediately.
Immediate Medical Attention
Seek medical attention immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, dry chemical or carbon dioxide. Water spray or fog.
Direct stream of water.
May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses. Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.
Keep unnecessary personnel away.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow product to enter sewer or waterways.
Ensure adequate ventilation. Remove all sources of ignition. Keep unnecessary personnel away. Wear appropriate personal protective equipment. Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean up. Scrape up spilled material and place in a closed container for disposal.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only with adequate ventilation. Vapours should be extracted to avoid inhalation. Remove all sources of ignition. Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Wear suitable protective clothing, safety glasses and gloves. See Section 8 of the SDS for Personal Protective Equipment. Keep container closed.
Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.
Wash thoroughly after handling.
Remove all sources of ignition. Keep in a cool, well ventilated area away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
None under normal processing.
Keep away from heat, ignition sources and incompatible materials.
This product may react with strong oxidizing agents.
Oxides of carbon. Oxides of nitrogen. Hydrocarbons
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TEROSON MS 9380 HPT BK FC570ML?
The signal word is warning.
What is the physical form of TEROSON MS 9380 HPT BK FC570ML?
TEROSON MS 9380 HPT BK FC570ML is a solid with black color. It has alcohol-like odor.
What is TEROSON MS 9380 HPT BK FC570ML used for?
adhesive and sealant
What are the hazard statements for TEROSON MS 9380 HPT BK FC570ML?
This substance has 1 hazard statement:
- H319: CAUSES SERIOUS EYE IRRITATION.
What is the melting point of TEROSON MS 9380 HPT BK FC570ML?
The melting point is Not applicable, Determination technically not possible and the boiling point is > 250 °C (> 482°F).