NextSDS Logo
Safety Data Sheet EN

LOCTITE Tyfo S Epoxy Part A Bulk Pail

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE Tyfo S Epoxy Part A Bulk Pail
Product Code
3154457

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Epoxy resin

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

http://www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Skin Irrit. Cat. 2
Eye Irrit. Cat. 2A
Skin Sens. Cat. 1

GHS Pictograms

GHS07 - Health hazard

GHS07

Hazard Statements

H315 CAUSES SKIN IRRITATION.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H319 CAUSES SERIOUS EYE IRRITATION.

Precautionary Statements

P261 Avoid breathing mist/vapours.
P264 Wash affected area thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, eye protection, and face protection.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Chemical Name CAS Number Concentration Hazardous
Epichlorohydrin-4,4'-isopropylidene diphenol resin 25068-38-6 80 - 100% Yes

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.

Skin contact

Rinse with running water and soap. Remove contaminated clothing and shoes. If symptoms develop and persist, get medical attention. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Seek medical attention immediately.

Ingestion

Seek immediate medical attention. Do not induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Seek immediate medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.

Instructions

Keep unnecessary personnel away. In case of fire, keep containers cool with water spray.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Ensure adequate ventilation. Remove all sources of ignition. Keep unnecessary personnel away. Wear appropriate personal protective equipment. Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.

Materials: sand, silica gel, acid binder, universal binder, sawdust

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wear suitable protective clothing, safety glasses and gloves. Keep container closed.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Store in a dry place. Store in original container until ready to use.

Hygiene

Wash thoroughly after handling. When using do not eat, drink or smoke.

Fire prevention

Remove all sources of ignition. Keep away from heat, spark and flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Use local ventilation if general ventilation is insufficient to maintain vapor concentration below established exposure limits.

Hands

gloves

Eyes

Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists.

Respiratory

Use NIOSH approved respirator if there is potential to exceed exposure limit(s).

Skin/Body

Use chemical resistant, impermeable clothing including gloves and either an apron or body suit to prevent skin contact.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
---
Colour
Colourless / Colorless to amber
Colour Intensity
---
Form
---
Odor
Mild
Odor Threshold
Not available.
Ph
Not applicable
Melting Point
-16 °C (3.2 °F)
Boiling Point
> 200 °C (> 392°F)
Flash Point
> 150 °C (> 302°F) Closed cup
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
---
Vapor Pressure
< 0.0000046 hPa (20 °C (68°F))
Vapor Density
---
Relative Density
1.16 at 25 °C (77°F)
Bulk Density
---
Density
---
Flammability
Not applicable
Upper Explosive Limit
---
Lower Explosive Limit
---
Explosive Limits
---
Auto Ignition Temperature
---
Decomposition Temperature
320 °C
Solubility
---
Partition Coefficient
---
Solubility In Water
Insoluble Water
Solubility In Fat
---
Molecular Weight
---
Voc Content
0 %
Metal Corrosion
---
Dynamic Viscosity
11,000 - 14,000 mPa.s
Kinematic Viscosity
---
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

High temperatures. Direct sunlight.

Incompatible

Oxidizing agents. Acids. Bases. Amines.

Decomposition

Oxides of carbon. Halogenated compounds. Phenolics. Aldehydes. Toxic fumes. Irritating vapors.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3082
Shipping Name
Environmentally hazardous substance, liquid, n.o.s. (Epoxy resin)
Transport Class
9
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE Tyfo S Epoxy Part A Bulk Pail?

The signal word is warning.

What is the physical form of LOCTITE Tyfo S Epoxy Part A Bulk Pail?

LOCTITE Tyfo S Epoxy Part A Bulk Pail is a liquid with colourless / colorless to amber color. It has mild odor.

What is LOCTITE Tyfo S Epoxy Part A Bulk Pail used for?

Epoxy resin

What are the hazard statements for LOCTITE Tyfo S Epoxy Part A Bulk Pail?

This substance has 3 hazard statements:

  • H315: CAUSES SKIN IRRITATION.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H319: CAUSES SERIOUS EYE IRRITATION.

What is the melting point of LOCTITE Tyfo S Epoxy Part A Bulk Pail?

The melting point is -16 °C (3.2 °F) and the boiling point is > 200 °C (> 392°F).