Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TECHNOMELT AS 4209
- Product Form
- Hotmelt adhesive
- Product Code
- 2010466
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Limestone | 1317-65-3 | 10 - 30% | Yes |
| Paraffin waxes and Hydrocarbon waxes | 8002-74-2 | 5 - 10% | Yes |
IDH number: 2010466 Product name: TECHNOMELT AS 4209
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms persist, seek medical advice.
Cool skin rapidly with cold water after contact with molten material. Cover affected areas with clean sheeting or gauze and seek immediate medical attention.
If eye contact occurs with molten material immediately cool with water. Do not remove adhesive. Seek medical attention.
Do not induce vomiting. Seek medical advice.
Immediate Medical Attention
Seek immediate medical attention for skin contact with molten material. Seek medical attention for eye contact with molten material.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
In case of fire, keep containers cool with water spray.
Wear self contained breathing apparatus.
Firefighter Protection
Wear self contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow material to contaminate ground water system.
Sweep up spilled material. Avoid creating dust. Keep in suitable and closed containers for disposal.
Materials: suitable and closed containers
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Do not place wet or damp solid into melt tank. Follow suggested application temperature. Always be careful around molten material. Avoid skin contact with molten resins. Do not wear contact lenses. Avoid dust formation.
store between -20 °C (-4°F) and 50 °C (122°F) Keep cool in accordance with information on label and in Technical Data Sheets.
Do not wear contact lenses.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
Will not occur.
Excessive heat.
Acids. Bases. Oxidizing agents.
Oxides of carbon.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TECHNOMELT AS 4209?
The signal word is warning.
What is the physical form of TECHNOMELT AS 4209?
TECHNOMELT AS 4209 is a solid appearing as beige with beige color. It has odorless odor.
What is the solubility of TECHNOMELT AS 4209?
Insoluble Water
What are the hazard statements for TECHNOMELT AS 4209?
This substance has 1 hazard statement:
- H320: CAUSES EYE IRRITATION.
What is the melting point of TECHNOMELT AS 4209?
The melting point is 160 °C (320°F) and the boiling point is > 280 °C (> 536°F).