Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE 3D IND406 Black
- Product Code
- 2730446
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
3D Printing
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 5-methyl-3-vinyl-1,3-oxazolidin-2-one | 3395-98-0 | 10 - 30% | Yes |
| Urethane acrylate | --- | 10 - 30% | Yes |
| Hydroxyalkyl methacrylate | --- | 5 - 10% | Yes |
| Acrylic ester | --- | 5 - 10% | Yes |
| Triacrylate ester | --- | 0.1 - 1% | Yes |
| UV Stabilizer | --- | 0.1 - 1% | Yes |
| Methacrylate | --- | 0.1 - 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.
Rinse with running water and soap. Remove contaminated clothing and shoes. Wash contaminated clothing before reuse. Discard any shoes or clothing items that cannot be decontaminated.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Seek medical attention immediately.
Seek immediate medical attention. Do not induce vomiting. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Seek medical attention immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, dry chemical or carbon dioxide.
Do not use high volume water jet.
Uncontrolled polymerization may occur at high temperatures resulting in explosions or rupture of storage containers.
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel. Refer to Section 8 'Exposure Controls / Personal Protection' prior to clean up.
Do not allow product to enter sewer or waterways.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up as much material as possible.
Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only with adequate ventilation. Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Keep container closed.
Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.
Wash thoroughly after handling.
Keep away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
None under normal processing. Polymerization may occur at elevated temperature or in the presence of incompatible materials.
Extremes of temperature and direct sunlight. Heat, flames, sparks and other sources of ignition. Store away from incompatible materials. UV light.
Strong reducing agents. Free radical initiators. Inert gases. Oxygen scavengers. Strong oxidizing agents. Amines, strong alkalies. Reactive metals. Acids. Iron. Rust. Peroxides.
Oxides of carbon. Oxides of nitrogen. Irritating organic vapours. Aldehydes. Hydrogen cyanide. Isocyanates.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE 3D IND406 Black?
The signal word is danger.
What is the physical form of LOCTITE 3D IND406 Black?
LOCTITE 3D IND406 Black is a liquid with black color. It has acrylate odor.
What is LOCTITE 3D IND406 Black used for?
3D Printing
What are the hazard statements for LOCTITE 3D IND406 Black?
This substance has 5 hazard statements:
- H302: HARMFUL IF SWALLOWED.
- H315: CAUSES SKIN IRRITATION.
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H318: CAUSES SERIOUS EYE DAMAGE.
- H335: MAY CAUSE RESPIRATORY IRRITATION.
What is the melting point of LOCTITE 3D IND406 Black?
The melting point is Not applicable, Product is a liquid and the boiling point is > 149 °C (> 300.2 °F).