NextSDS Logo
Safety Data Sheet EN

LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG
Product Code
1188757

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Epoxy adhesive

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Skin Irrit. Cat. 2
Eye Irrit. Cat. 2A
Skin Sens. Cat. 1
Carc. Cat. 2
STOT RE Cat. 2

GHS Pictograms

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H315 CAUSES SKIN IRRITATION.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H319 CAUSES SERIOUS EYE IRRITATION.
H351 SUSPECTED OF CAUSING CANCER.
H372 MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe dust or fumes.
P264 Wash affected area thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P352 IF ON SKIN: Wash with plenty of water.
P362 Take off contaminated clothing.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Epichlorohydrin-4,4'-isopropylidene diphenol resin 25068-38-6 30 - 60% No
Epoxy resin --- 10 - 30% No
Epoxy resin --- 5 - 10% No
Diuron 330-54-1 5 - 10% No
Siloxanes and Silicones, di-Me, reaction products with silica 67762-90-7 1 - 5% No
Filler --- 1 - 5% No
Titanium dioxide 13463-67-7 1 - 5% No
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.

Skin contact

Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and footwear. Wash clothing before reuse. If symptoms develop and persist, get medical attention.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Ingestion

DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention.

Immediate Medical Attention

Get medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

Closed containers may rupture (due to build up of pressure) when exposed to extreme heat. This product is combustible at high temperatures.

Instructions

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Ensure adequate ventilation. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Store in a partly filled, closed container until disposal.

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

For industrial use only. Use only with adequate ventilation. Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Refer to Section 8.

Storage

For safe storage, store between 0 °C (32°F) and 4 °C (39.2 °F). Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.

Hygiene

Wash thoroughly after handling.

Fire prevention

Keep in a cool, well ventilated area away from heat, sparks and open flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Solubility
---
Crystallisation Point
---
Dynamic Viscosity
---
Physical State
Paste
Odor Threshold
Not available.
Appearance
---
Properties Status
---
Form
---
Solidification Point
---
Boiling Point
Polymerization.
Evaporation Rate
Not available.
Colour
Gray
Relative Evaporation Rate
---
Solubility In Water
Insoluble
Metal Corrosion
---
Voc Content
< 1 %; < 5 g/l
Auto Ignition Temperature
Not available.
Softening Point
---
Physical State Data
liquid
Vapor Density
Not applicable
Vapor Pressure
Not applicable
Upper Explosive Limit
Not available.
Cloud Point
---
Flammability
Not applicable
State Under Standard Conditions
---
Solubility In Fat
---
Odor
Slight
Melting Point
Not available.
Explosive Limits
---
Lower Explosive Limit
Not available.
Kinematic Viscosity
---
Ph
Not available.
Decomposition Temperature
Not available.
Bulk Density
---
Relative Density
---
Partition Coefficient
Not available.
Flash Point
> 200 °F (> 93.33 °C)
Molecular Weight
---
Freezing Point
---
Colour Intensity
---
Density
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing. Polymerization may occur at elevated temperature or in the presence of incompatible materials.

Avoid

Elevated temperatures.

Incompatible

Strong oxidizing agents (peroxides, chlorine, strong acids). Amines.

Decomposition

Oxides of carbon. Hazardous decomposition products include chlorine compounds. Hydrocarbons.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3077
Shipping Name
RQ, Environmentally hazardous substance, solid, n.o.s.
Transport Class
9
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG?

The signal word is warning.

What is the physical form of LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG?

LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG is a paste with gray color. It has slight odor.

What is LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG used for?

Epoxy adhesive

What are the hazard statements for LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG?

This substance has 5 hazard statements:

  • H315: CAUSES SKIN IRRITATION.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H319: CAUSES SERIOUS EYE IRRITATION.
  • H351: SUSPECTED OF CAUSING CANCER.
  • H372: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of LOCTITE ABLESTIK G 909 known as ECCOBOND G-909 5GA PAIL 21.55KG?

The melting point is Not available. and the boiling point is Polymerization..