NextSDS Logo
Safety Data Sheet EN

LOCTITE ECCOBOND UF 3915FL 30ML

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE ECCOBOND UF 3915FL 30ML
Product Code
2957823

Regulatory Identifiers

CAS Number
N/A

Identified Uses

1-c- epoxide adhesive

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Irrit. Cat. 2
Eye Dam. Cat. 1
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
STOT SE Cat. 3

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H315 CAUSES SKIN IRRITATION.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H318 CAUSES SERIOUS EYE DAMAGE.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H335 MAY CAUSE RESPIRATORY IRRITATION.

Precautionary Statements

P261 Avoid breathing mist/vapours.
P264 Wash affected area thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, eye protection, and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

* Hazardous Component(s) | CAS Number | Weight %* (table provided in section 3)

Chemical Name CAS Number Concentration Hazardous
Silica, vitreous 60676-86-0 30 - 60% Yes
hexahydro-4-methylphthalic anhydride 19438-60-9 10 - 30% Yes
Bisphenol-F Epichlorhydrin resin 9003-36-5 5 - 10% Yes
cyclohexane-1,2-dicarboxylic anhydride 85-42-7 5 - 10% Yes
Hexanedioic acid, 1,6-bis(7-oxabicyclo[4.1.0]hept-3-ylmethyl) ester 3130-19-6 1 - 5% Yes
Epichlorohydrin-4,4'-isopropylidene diphenol resin 25068-38-6 1 - 5% Yes

Notes

Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.

Skin contact

Remove contaminated clothing and shoes. Rinse with running water and soap. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated. If symptoms develop and persist, get medical attention.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Seek medical attention immediately.

Ingestion

Never give anything by mouth to an unconscious person. DO NOT induce vomiting unless directed to do so by medical personnel.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.

Instructions

Keep unnecessary personnel away.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Ensure adequate ventilation. Remove all sources of ignition. Keep unnecessary personnel away. Wear appropriate personal protective equipment. Refer to Section 8 'Exposure Controls / Personal Protection' prior to clean up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.

Materials: sand, silica gel, acid binder, universal binder, sawdust

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wear suitable protective clothing, safety glasses and gloves. Keep container closed.

Storage

Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.

Hygiene

Wash thoroughly after handling. When using do not eat, drink or smoke.

Fire prevention

Remove all sources of ignition. Keep away from heat, sparks and open flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Metal Corrosion
---
Odor
Mild
Upper Explosive Limit
---
Voc Content
---
Freezing Point
---
Physical State Data
liquid
Flammability
Not applicable
Cloud Point
---
Solubility In Fat
---
Physical State
Liquid
Relative Density
1.6
Vapor Density
---
Softening Point
---
Decomposition Temperature
---
Lower Explosive Limit
---
Appearance
---
Properties Status
---
Flash Point
> 93 °C (> 199.4 °F)
Melting Point
---
Evaporation Rate
---
Relative Evaporation Rate
---
Molecular Weight
---
Vapor Pressure
---
State Under Standard Conditions
---
Solidification Point
---
Odor Threshold
---
Colour Intensity
---
Kinematic Viscosity
---
Boiling Point
---
Explosive Limits
---
Bulk Density
---
Crystallisation Point
---
Dynamic Viscosity
4,000 - 8,000 cp
Colour
Black
Ph
---
Auto Ignition Temperature
---
Density
---
Solubility
---
Partition Coefficient
---
Form
---
Solubility In Water
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. Protect from direct sunlight.

Incompatible

Oxidizing agents. Acids. Bases. Amines. Strong oxidizing agents. Strong acids and strong bases. Amines.

Decomposition

Oxides of carbon. Phenolics. Toxic fumes. Irritating vapors.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

Shipping Name
Not regulated
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE ECCOBOND UF 3915FL 30ML?

The signal word is danger.

What is the physical form of LOCTITE ECCOBOND UF 3915FL 30ML?

LOCTITE ECCOBOND UF 3915FL 30ML is a liquid with black color. It has mild odor.

What is LOCTITE ECCOBOND UF 3915FL 30ML used for?

1-c- epoxide adhesive

What are the hazard statements for LOCTITE ECCOBOND UF 3915FL 30ML?

This substance has 5 hazard statements:

  • H315: CAUSES SKIN IRRITATION.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H318: CAUSES SERIOUS EYE DAMAGE.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H335: MAY CAUSE RESPIRATORY IRRITATION.