Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE EA 9359.3 AERO PART A 50ML
- Product Code
- 937133
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Part A of 2-K-Epoxy Adhesive
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2,2'-[(1-Methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane | 1675-54-3 | 30 - 60% | Yes |
| Triglycidyl-p-aminophenol | 5026-74-4 | 10 - 30% | Yes |
| Epichlorohydrin-4,4'-isopropylidene diphenol resin | 25068-38-6 | 5 - 10% | Yes |
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.
Remove contaminated clothing and footwear. Wash with soap and water. If a person feels unwell or symptoms of skin irritation appear, consult a physician.
In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention.
DO NOT induce vomiting unless directed to do so by medical personnel. If symptoms develop and persist, get medical attention.
Immediate Medical Attention
In case of contact with the eyes, seek immediate medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.
Wear full protective clothing. Wear self-contained breathing apparatus.
Firefighter Protection
Wear full protective clothing. Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so. Wear appropriate protective equipment and clothing during clean-up. Do not allow product to enter sewer or waterways.
Absorb spill with inert material. Shovel material into appropriate container for disposal.
Materials: inert material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Follow curing schedule as recommended in product literature. Empty containers retain product residue, so obey hazard warnings and handle empty containers as if they were full. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. For industrial use only.
Store at or below 25 °C (77°F). Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Keep away from heat, spark and flame.
Wash thoroughly after handling.
Keep away from heat, spark and flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
May occur.
Avoid mixing resin (Part A) and curing agent (Part B) unless you plan to use immediately. Do not heat mixed adhesive unless you plan to use immediately. Failure to observe these precautions may result in excessive heat build-up causing an exotherm.
Keep away from strong oxidizing agents, strong Lewis or mineral acids.
Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN3077
- Shipping Name
- Environmentally hazardous substance, solid, n.o.s. (Bisphenol-A Epichlorhydrin resin, Triglycidyl-p-aminophenol)
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE EA 9359.3 AERO PART A 50ML?
The signal word is warning.
What is the physical form of LOCTITE EA 9359.3 AERO PART A 50ML?
LOCTITE EA 9359.3 AERO PART A 50ML is a paste appearing as paste with yellow color. It has epoxy odor.
What is the solubility of LOCTITE EA 9359.3 AERO PART A 50ML?
Not soluble Water; Partially miscible ketones
What is LOCTITE EA 9359.3 AERO PART A 50ML used for?
Part A of 2-K-Epoxy Adhesive
What are the hazard statements for LOCTITE EA 9359.3 AERO PART A 50ML?
This substance has 4 hazard statements:
- H315: CAUSES SKIN IRRITATION.
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H319: CAUSES SERIOUS EYE IRRITATION.
- H341: SUSPECTED OF CAUSING GENETIC DEFECTS.
What is the melting point of LOCTITE EA 9359.3 AERO PART A 50ML?
The melting point is -26 °C (-14.8 °F) and the boiling point is > 200 °C (> 392°F).