Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE STYCAST 5877 PTB
- Product Code
- 1188226
- Synonyms
- STYCAST 5877 PTB 1LB GA
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Silicone adhesive
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelina.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Siloxanes and silicones, dimethyl, methyl hydrogen | 68037-59-2 | 30 - 60% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and footwear. If symptoms develop and persist, get medical attention. Wash clothing before reuse.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.
DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Isolate the hazard area and deny entry to unnecessary and unprotected personnel. Evacuate and ventilate spill area; dike spill to prevent entry into water system; wear full protective equipment during clean-up.
Do not allow product to enter sewer or waterways.
Soak up with inert absorbent material. Wash spillage site thoroughly with soap and water or detergent solution.
Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust), soap and water or detergent solution
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only with adequate ventilation. Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Refer to Section 8.
Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.
Wash thoroughly after handling.
Keep away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate local exhaust ventilation to maintain worker exposure below exposure limits.
Use impermeable gloves
Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists. Safety showers and eye wash stations should be available.
Use NIOSH approved respirator if there is potential to exceed exposure limit(s).
protective clothing as necessary to prevent skin contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
None under normal processing.
Elevated temperatures. Heat, flames, sparks and other sources of ignition. Store away from incompatible materials.
Oxidizing agents. Strong acids and strong bases. Powdered metals. Metal oxides.
Oxides of carbon. Oxides of silicon. Formaldehyde. Irritating organic vapours.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What other names is LOCTITE STYCAST 5877 PTB known by?
LOCTITE STYCAST 5877 PTB is also known as: STYCAST 5877 PTB 1LB GA
What is the hazard signal word for LOCTITE STYCAST 5877 PTB?
The signal word is warning.
What is the physical form of LOCTITE STYCAST 5877 PTB?
LOCTITE STYCAST 5877 PTB is a liquid with colourless / colorless color. It has slight odor.
What is the solubility of LOCTITE STYCAST 5877 PTB?
Insoluble Water
What is LOCTITE STYCAST 5877 PTB used for?
Silicone adhesive
What are the hazard statements for LOCTITE STYCAST 5877 PTB?
This substance has 3 hazard statements:
- H315: CAUSES SKIN IRRITATION.
- H319: CAUSES SERIOUS EYE IRRITATION.
- H335: MAY CAUSE RESPIRATORY IRRITATION.
What is the melting point of LOCTITE STYCAST 5877 PTB?
The melting point is Not available. and the boiling point is Not available..