Zinc sulfate heptahydrate

If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.

Symptoms: Zinc oxide dust or fume can irritate the respiratory tract. Coughing, metallic taste, marked thirst, fatigue, weakness, muscular pain, fever, chills. Severe overexposure may result in bronchitis or pneumonia. Cough, wheezing, laryngitis, shortness of breath, airway resistance, pulmonary edema.

Wash off with soap and plenty of water. Consult a physician.

Symptoms: Prolonged skin contact can produce a severe dermatitis called oxide pox. Bluish tint to the skin. Burning sensation.

Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.

Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician.

Symptoms: Nausea, vomiting, metallic taste, marked thirst, fatigue, weakness, muscular pain, fever, chills.

Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.

Sulphur oxides, Borane/boron oxides, Zinc/zinc oxides

Use personal protective equipment. Avoid dust formation. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust.

Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the environment must be avoided.

Pick up and arrange disposal without creating dust. Sweep up and shovel.

Materials: suitable, closed containers

Avoid contact with skin and eyes. Avoid formation of dust and aerosols.

Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Hygroscopic.

Handle in accordance with good industrial hygiene and safety practice.

Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it. Immersion protection: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: > 480 min, Material tested:Dermatril® (Aldrich Z677272, Size M). Splash protection: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: > 30 min, Material tested:Dermatril® (Aldrich Z677272, Size M). data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 873000, e-mail sales@kcl.de, test method: EN374. If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the CE approved gloves. This recommendation is advisory only and must be evaluated by an Industrial Hygienist familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario.

Face shield and safety glasses Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).

Where risk assessment shows air-purifying respirators are appropriate use a full-face particle respirator type N100 (US) or type P3 (EN 143) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).

Complete suit protecting against chemicals, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.

no data available

no data available

no data available

no data available

Strong oxidizing agents

Other decomposition products - no data available

EHS-Mark required (ADR 2.2.9.1.10) for single packagings and combination packagings containing inner packagings with Dangerous Goods > 5L for liquids or > 5kg for solids.

EHS-Mark required (IMDG code 2.10.3) for single packagings and combination packagings containing inner packagings with Dangerous Goods > 5L for liquids or > 5kg for solids.

EHS-Mark required for single packagings and combination packagings containing inner packagings with Dangerous Goods > 5L for liquids or > 5kg for solids.