Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Dinophysistoxin-1 (sodium salt)
- Product Code
- CIF-CRM-DTX1
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Reference material for laboratory use only
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
LGC Limited
manufacturer
Queens Road, Teddington, Middlesex TW11 0LY, UNITED KINGDOM
+44 (0) 20 8943 7000
http://www.lgcstandards.com
Emergency Contacts
Emergency Contact
+44 (0) 20 8943 7000
Monday - Friday : 8am - 5pm
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS06
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Methanol EC: 200-659-6 | 67-56-1 | 99% | Yes |
| Dinophysistoxin-1 (sodium salt) | 81720-10-7 | 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air or oxygen; call for doctor. In case of unconsciousness place patient in recovery position for transport. Seek immediate medical advice.
Immediately wash with water and soap and rinse thoroughly. Seek immediate medical advice.
Rinse opened eye for several minutes under running water. Then consult a doctor.
Rinse mouth. Do not induce vomiting. Call a doctor immediately. Call for a doctor immediately.
Immediate Medical Attention
Seek immediate medical advice.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
During heating or in case of fire poisonous gases are produced.
Firefighter Protection
Mouth respiratory protective device. Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Mount respiratory protective device. Wear protective equipment. Keep unprotected persons away.
Dilute with plenty of water.
Absorb with liquid-binding material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/extraction at the workplace. Open and handle receptacle with care. Prevent formation of aerosols.
Store in cool, dry place in tightly closed receptacles.
Keep ignition sources away - Do not smoke. Protect against electrostatic charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation The protective gloves to be used must comply with the specifications of EC Directive 89/686/EEC and the related standard EN374. Protective gloves. Material of gloves Butyl rubber, BR. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device. Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions.
Stable under normal conditions.
No dangerous reactions known.
heating or in case of fire
Strong oxidizing agents. Strong acids. Reducing agents. Alkali metals.
toxic gases
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1230
- Shipping Name
- METHANOL mixture
- Transport Class
- 3
- Packing Group
- II
Warning: Flammable liquids.
Warning: Flammable liquids. Stowage Category B. SW2 Clear of living quarters.
Warning: Flammable liquids.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Dinophysistoxin-1 (sodium salt)?
The signal word is danger.
What is the physical form of Dinophysistoxin-1 (sodium salt)?
Dinophysistoxin-1 (sodium salt) is a liquid appearing as form: liquid colour: colourless with colourless color. It has alcohol-like odor.
What is Dinophysistoxin-1 (sodium salt) used for?
Reference material for laboratory use only
What are the hazard statements for Dinophysistoxin-1 (sodium salt)?
This substance has 3 hazard statements:
- H225: Highly flammable liquid and vapour.
- H301 + H311 + H331: Toxic if swallowed, in contact with skin or if inhaled.
- H370: Causes damage to organs.
What is the melting point of Dinophysistoxin-1 (sodium salt)?
The melting point is -98 °C and the boiling point is 65 °C.