Diethyl ether dried (max. 0.005 % H2O) SeccoSolv®

After inhalation: fresh air. Call in physician.

In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.

After eye contact: rinse out with plenty of water. Remove contact lenses.

After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.

Carbon dioxide (CO2) Foam Dry powder

For this substance/mixture no limitations of extinguishing agents are given.

Combustible. Pay attention to flashback. Vapors are heavier than air and may spread along floors. Development of hazardous combustion gases or vapours possible in the event of fire. Forms explosive mixtures with air at ambient temperatures.

Remove container from danger zone and cool with water.

Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition. Evacuate the danger area, observe emergency procedures, consult an expert.

Do not let product enter drains. Risk of explosion.

Take up with liquid-absorbent material (e.g. Chemizorb®). Dispose of properly. Clean up affected area.

Materials: liquid-absorbent material (e.g. Chemizorb®)

Work under hood. Do not inhale substance/mixture. Avoid generation of vapours/aerosols.

Protected from light. Keep container tightly closed in a dry and well-ventilated place. Keep away from heat and sources of ignition. Recommended storage temperature see product label.

Change contaminated clothing. Preventive skin protection recommended. Wash hands after working with substance.

Keep away from open flames, hot surfaces and sources of ignition.

This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Splash contact Material: Viton® Minimum layer thickness: 0,7 mm Break through time: 30 min Material tested: Vitoject® (KCL 890 / Aldrich Z677698, Size M)

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses

required when vapours/aerosols are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type AX The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.

Flame retardant antistatic protective clothing.

Do not let product enter drains. Risk of explosion.

The product is chemically stable under standard ambient conditions (room temperature). Contains the following stabilizer(s): butyl hydroxytoluene (BHT) (<0,0010,0009 %)

Formation of peroxides possible.

Risk of ignition or formation of inflammable gases or vapours with: chromyl chloride, Peroxides. Risk of explosion with: azides, halogens, halogen-halogen compounds, nonmetallic oxyhalides, Strong oxidizing agents, chromium(VI) oxide, halogen oxides, peroxi compounds, perchloric acid, perchlorates, Nitric acid, nitrating acid, Oxygen, Ozone, turpentine oils and/or turpentine substitutes, nitrates, metallic chlorides, salts of oxyhalogenic acids, nitrogen oxides, nonmetallic oxides, chromosulfuric acid, chlorates, hydrogen peroxide, permanganic acid, sulfuric acid. Risk of explosion during distillation. Exothermic reaction with: acid halides. With Nitric acid, sulfur.

Light. Heat. Air. Warming. Moisture.

chromyl chloride, Peroxides, azides, halogens, halogen-halogen compounds, nonmetallic oxyhalides, Strong oxidizing agents, chromium(VI) oxide, halogen oxides, peroxi compounds, perchloric acid, perchlorates, Nitric acid, nitrating acid, Oxygen, Ozone, turpentine oils and/or turpentine substitutes, nitrates, metallic chlorides, salts of oxyhalogenic acids, nitrogen oxides, nonmetallic oxides, chromosulfuric acid, chlorates, hydrogen peroxide, permanganic acid, sulfuric acid, acid halides, sulfur

Peroxides