Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- 231016 Foam Cleaner
Regulatory Identifiers
- CAS Number
- N/A
- UFI Code
- F7PU-KWWY-EDCW-87C6
Identified Uses
Cleaner (AISE_SUMI_PW_11_1_G)
Manufacturers & Suppliers
BOMA
distributor
Noorderlaan 131, B2030 Antwerpen
003232313389
http://www.boma.eu/
Emergency Contacts
Emergency Contact
+32 70 245 245
Nationaal Vergiftigingen Informatie Centrum (NVIC)
+31 88 755 8000
Emergency Contact
+ 33 (0)1 45 42 59 59
Emergency Contact
(+352) 8002-5500
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| n-Butane (<0,01% Butadiene -1,3) EC: 203-448-7 | 106-97-8 | 8% | Yes |
| 2-butoxyethanol EC: 203-905-0 | 111-76-2 | 8% | Yes |
| Isobutane EC: 200-857-2 | 75-28-5 | 3% | Yes |
| Propane EC: 200-827-9 | 74-98-6 | 3% | Yes |
| Sodium nitrite EC: 231-555-9 | 7632-00-0 | 3% | Yes |
| Fattyalcohol C8-10, ethoxylated EC: 615-247-5 | 71060-57-6 | 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Let sit upright, fresh air, rest and take to hospital.
Symptoms: Sore throat, cough, shortness of breath, headache
Remove contaminated clothing, rinse skin with plenty of water, if necessary seek medical attention.
Symptoms: Redness, pain
Thoroughly rinse with water (contact lenses to be removed if this is easily done) then take to physician.
Symptoms: Redness, pain, blurred vision
Rinse mouth, do not induce vomiting, take to hospital immediately.
Symptoms: Diarrhoea, headache, abdominal cramps, sleepiness, vomiting
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, foam, powder, sprayed water
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not walk into or touch spilled substances and avoid inhalation of fumes, smoke, dusts and vapours by staying up wind. Remove any contaminated clothing and used contaminated protective equipment and dispose of it safely.
Do not allow to flow into sewers or open water.
If possible, remove by using absorbent material.
Materials: absorbent material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Handle with care to avoid spillage.
Keep in a sealed container in a closed, frost-free, ventilated room.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The level of protection and types of controls necessary will vary depending upon potential exposure conditions. Adequate ventilation should be provided so that exposure limits are not exceeded. For further information, check section 7.
Handling with Viton-gloves (EN 374). Breakthrough time: >480' Material thickness: 0,7 mm. Thoroughly check gloves before use. Take of the gloves properly without touching the outside with your bare hands. The manufacturer of the protective gloves has to be consulted about the suitability for a specific work station. Wash and dry your hands.
Keep an eye-rinse bottle within reach. Tight-fitting safety goggles. Wear a face shield and protective suit in case of exceptional processing problems.
Respiratory protection is not required. Use ABEK type gas masks in case of irritating exposure. If necessary, use with sufficient exhaust ventilation.
Wear impermeable clothing. The type of protective equipment depends on the concentration and amount of hazardous substances at the work station in question.
Comply with applicable environmental regulations limiting discharge to air, water and soil. Protect the environment by applying appropriate control measures to prevent or limit emissions. For further information, check sections 6 and 13.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Extremely high or low temperatures.
Stable under normal conditions.
Protect from sunlight and do not expose to temperatures exceeding + 50°C.
Keep away from sources of ignition
Under recommended usage conditions, hazardous decomposition products are not expected.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- Aerosols, flammable
- Transport Class
- 5F
Risk of fire. Risk of explosion. Containments may explode when heated. Take cover. Keep out of low areas.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for 231016 Foam Cleaner?
The signal word is danger.
What is the physical form of 231016 Foam Cleaner?
231016 Foam Cleaner is a liquid appearing as liquid with colourless color. It has characteristic odor.
What is 231016 Foam Cleaner used for?
Cleaner (AISE_SUMI_PW_11_1_G)
What are the hazard statements for 231016 Foam Cleaner?
This substance has 3 hazard statements:
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
- H319: Causes serious eye irritation.