Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- INDUSTRIAL HYDRAULIC OIL
- Product Code
- 184
- Synonyms
- ISO GRADES 22, 32, 46, 68, 100, 150, MV22, HVI 36
Regulatory Identifiers
- CAS Number
- Mixture Check regulations →
Identified Uses
Hydraulic oil.
Manufacturers & Suppliers
Consumers' Co-operative Refineries Limited
manufacturer
P.O. Box 260; 9th Avenue North Regina, SK S4P 3A1 Canada
(306) 721-5353
Federated Co-operatives Limited
distributor
P.O. Box 1050, 401 - 22nd Street East Saskatoon SK S7K 3M9 Canada
(306) 244-3447
Emergency Contacts
Canutec
(613) 996-6666
24 Hour
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
GHS07
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
The manufacturer lists no ingredients as hazardous according to OSHA 29 CFR 1910.1200.
First Aid Measures
Emergency procedures for chemical exposure incidents
If fumes or combustion products are inhaled move victim to fresh air. Get medical attention if any discomfort occurs.
In case of contact, flush skin with plenty of water for at least 20 minutes, while removing contaminated shoes and clothes. Wash contaminated skin with soap and water. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Get medical attention if irritation develops and persists.
Check for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 20 minutes, occasionally lifting the upper and lower eyelids. Get medical attention if symptoms occur.
Do not induce vomiting. Never give anything by mouth to an unconscious person. Get medical attention if any discomfort occurs.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Extinguish with water spray, carbon dioxide, dry chemical or material appropriate for the surrounding fire.
None.
By heating and fire, toxic vapors/gases may be formed.
Use standard firefighting procedures and consider the hazards of other involved materials.
Firefighter Protection
Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid discharge into drains, water courses or onto the ground. Prevent spreading over a wide area (e.g. by containment or oil barriers).
Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers.
Materials: dry earth, sand or other non-combustible material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Observe good industrial hygiene practices. Use appropriate Personal Protective Equipment.
Store in original tightly closed container. Keep in a cool, well-ventilated place.
Observe good industrial hygiene practices.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
General ventilation is normally adequate.
Wear protective gloves. Neoprene or nitrile gloves are recommended.
Wear approved safety glasses or goggles.
No personal respiratory protective equipment normally required.
Wear appropriate clothing to prevent repeated or prolonged skin contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Material is stable under normal conditions.
Will not occur.
No data available.
None known.
None expected under normal conditions of use.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What other names is INDUSTRIAL HYDRAULIC OIL known by?
INDUSTRIAL HYDRAULIC OIL is also known as: ISO GRADES 22, 32, 46, 68, 100, 150, MV22, HVI 36
What is the hazard signal word for INDUSTRIAL HYDRAULIC OIL?
The signal word is warning.
What is the physical form of INDUSTRIAL HYDRAULIC OIL?
INDUSTRIAL HYDRAULIC OIL is a liquid. appearing as oily liquid. with brown. color. It has mild. odor.
What is INDUSTRIAL HYDRAULIC OIL used for?
Hydraulic oil.
What are the hazard statements for INDUSTRIAL HYDRAULIC OIL?
This substance has 6 hazard statements:
- H315: Prolonged skin contact may cause temporary irritation.
- H319: Direct contact with eyes may cause temporary irritation.
- H335: May cause respiratory tract irritation.
- Low hazard for usual industrial or commercial handling by trained personnel.
- Under normal conditions of intended use, this material does not pose a risk to health.
- No special environmental precautions required.
What is the melting point of INDUSTRIAL HYDRAULIC OIL?
The melting point is 14 °F (-10 °C) and the boiling point is Not available..