Yale 10W-30 SL/GF2

Allow the victim to rest. Assure fresh air breathing.

Remove affected clothing and wash all exposed skin area with mild soap and water, followed by warm water rinse. Seek medical attention if ill effect or irritation develops. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency.

Check for and remove contact lenses. Ensure adequate flushing of eyes by separating eyelids with the fingers. Rinse immediately with plenty of water. Obtain medical attention if pain, blinking or redness persist.

Symptoms: pain, blinking or redness

Rinse mouth. Do not induce vomiting. If vomiting occurs spontaneously, keep head below the hips to prevent aspiration. Never give anything by mouth to an unconscious person.

Symptoms: Vomiting after ingestion may cause aspiration into the lungs, which may cause severe lungdamage or death.

Water fog. Dry powder. Carbon dioxide. Foam.

Do not use a heavy water stream.

When exposed to heat, may decompose liberating hazardous gases.

Exercise caution when fighting any chemical fire.

Avoid contact with skin and eyes. Equip cleanup crew with proper protection. Spill area may be slippery.

Take up large spills with pump or vacuum.

For large spills dike spilled material or otherwise contain material to ensure runoff does not reach a waterway. Recover the cleaning water for later diposal. Prevent entry to sewers and public waters.

Take up large spills with pump or vacuum. Absorb with liquid-binding material ( sand, diatomite, acid binders, universal binders, sawdust).

Materials: sand, diatomite, acid binders, universal binders, sawdust

Avoid contact with skin and eyes. Where contact with eyes or skin is likely, wear suitable protection. Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and when leaving work. Wash clothing before re-using.

Store in tightly closed, properly ventilated containers away from heat, sparks, open flame. Always keep in containers of same material as the original one. Do not store in open or unlabelled containers.

Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and when leaving work. Wash clothing before re-using.

Store in tightly closed, properly ventilated containers away from heat, sparks, open flame. Cloth, paper and other materials that are used to absorb spills present a fire hazard.

adequate natural or local exhaust ventilation

In case of repeated or prolonged contact wear gloves. The gloves should be replaced immediately in case of damage or signs of wear. It is recommended to use preventative skin protection (skin cream). Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion, and the contact time. The protection glove should be tested for its specific suitability (e.g. mechanical strength, product compatibility, anti-static properties). Material: Nitril. Thickness (mm): 0.4, Breakthrough time (min): 480, Level: 6, according: EN 374. Material: Neoprene. Thickness (mm): 0.65, Breakthrough time (min): 60, Level: 3, according: EN 374.

Safety glasses with side shields. Eye protection should only be necessary where liquid could be splashed or sprayed.

Respiratory protective equipment is not normally required where there is adequate natural or local exhaust ventilation to control exposure. Where excessive vapour, mist, or dust may result, use approved respiratory protection equipment. Respiratory protective equipment must be checked to ensure it fits correctly each time it is worn. Provided an air-filtering/air-purifying respirator is suitable, a filter for particulates can be used for mist or fume. Use filter type P or comparable standard. A combination filter for particles and organic gases and vapours (boiling point > 65°C) may be required if vapour or abnormal odour is also present due to high product temperature. Use filter type AP or comparable standard.

No special clothing/skin protection equipment is recommended under normal conditions of use. Avoid repeated or prolonged skin contact. If repeated skin contact or contamination of clothing is likely, protective clothing should be worn. Cotton or polyester/cotton overalls will only provide protection against light superficial contamination that will not soak through to the skin. Overalls should be laundered on a regular basis. When the risk of skin exposure is high (e.g. when cleaning up spillages or if there is a risk of splashing) then chemical resistant aprons and/or impervious chemical suits and boots will be required.

See Heading 6. See Heading 12.

Stable under normal conditions.

None under normal conditions. Hazardous polymerization: Will not occur.

See Heading 6. See Heading 7. See Heading 15.

May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides, etc.

On exposure to high temperature, may decompose, releasing toxic/flammable vapours. CO, CO2, POx, NOx, SOx, H2S Metal oxides.