Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Marking Ink NPO / PO
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Marking ink for metal substrates
Manufacturers & Suppliers
Dunia Coatings
manufacturer
Planckstraat 21, 3361 GS Dordrecht
+31(78)-6540478
Emergency Contacts
National Information Center
+31(0) 30 - 274 88 88
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Solvent mixture with additives
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Methoxy-2-Propylacetate | 108-65-6 | 2.5 - 10% | Yes |
| n-Butylacetate | 123-42-2 | 20 - 25% | Yes |
| Solvent Nafta 90/170 | 64742-95-6 | 1 - 2.5% | Yes |
| DiacetonAlcohol | 123-42-2 | 25 - 50% | Yes |
| Xyleen | 1330-20-7 | 1 - 2.5% | Yes |
| Ethanol | 64-17-5 | 1 - 2.5% | Yes |
| Cellulose nitrate | --- | 7 - 10% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Take the casualty into the fresh air and keep warm. Irregular breathing/no breathing: artificial respiration. Call a physician.
Remove contaminated clothing. Wash away with soap and water and rinse. Do NOT use solvents or thinners.
Contact lenses should be removed. Flush with plenty of water ( 10 - 15 min. ) holding the eyelids apart and seek medical advice.
Rinse mouth and give water. If accidentally swallowed obtain immediate medical attention. Keep patient at rest. Do not induce vomiting.
Immediate Medical Attention
In all cases of doubt, or when symptoms persist, seek medical attention. Call a physician. Seek medical advice. If accidentally swallowed obtain immediate medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
alcohol resistant foam, CO2, powder, water spray/mist.
water jet.
Fire will produce dense black smoke containing hazardous products of combustion ( see Section 10). Decomposition products may be a hazard to health.
Cool closed containers exposed to fire with water spray.
Firefighter Protection
Appropriate self-contained breathing apparatus may be required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not empty into drains. If the product contaminates lakes, rivers or sewages, inform appropriate authorities in accordance with the local regulations.
Clean preferably with a detergent; avoid use of solvents.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Vapours are heavier than air and may spread along floors. Prevent the creation of flammable or explosive concentrations of vapour in air and avoid vapour concentration higher than the occupational exposure limits. Keep the container tightly closed. Avoid skin and eye contact. Avoid inhalation of vapour and spray mist. Smoking, eating and drinking should be prohibited in areas of storage and use. Never use pressure to empty; the container is not a pressure vessel. Always keep in containers made of the same material as the supply container.
Store in a dry, well ventilated place away from sources of heat, ignition and direct sunlight. No smoking. Prevent unauthorized access. Containers which are opened should be properly resealed and kept upright to prevent leakage.
Smoking, eating and drinking should be prohibited in areas of storage and use.
Exclude sources of heat, sparks and open flame. Non-sparking tools should be used. Good housekeeping standards and regular safe removal of waste material will minimize risks of spontaneous combustion and other fire hazards.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate ventilation. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction.
If these are not sufficient to maintain concentrations of particulates and/or solvent vapour below the OEL, suitable respiratory protections must be worn.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage and handling conditions ( see section 7 ).
Keep away from oxidizing agents, strongly alkaline and strongly acid materials in order to avoid exothermic reactions.
oxidizing agents, strongly alkaline and strongly acid materials
smoke, carbon monoxide and oxides of nitrogen
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1263
- Shipping Name
- Paint
- Transport Class
- 3
- Packing Group
- II (ADR/RID), III (ICAO)
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Marking Ink NPO / PO?
The signal word is na: r-phrases.
What is the physical form of Marking Ink NPO / PO?
Marking Ink NPO / PO is a liquid with several color. It has characteristic odor.
What is Marking Ink NPO / PO used for?
Marking ink for metal substrates