PATTERN COAT BLACK

Remove to open air. If the subject stops breathing, administer artificial respiration. Get medical advice/attention immediately.

Remove contaminated clothing. Rinse skin with a shower immediately. Get medical advice/attention immediately. Wash contaminated clothing before using it again.

Remove contact lenses, if present. Wash immediately with plenty of water for at least 15 minutes, opening the eyelids fully. If problem persists, seek medical advice.

Get medical advice/attention immediately. Do not induce vomiting. Do not administer anything not explicitly authorised by a doctor.

carbon dioxide, foam, chemical powder. For product loss or leakage that has not caught fire, water spray can be used to disperse flammable vapours and protect those trying to stem the leak.

Do not use jets of water. Water is not effective for putting out fires but can be used to cool containers exposed to flames to prevent explosions.

Excess pressure may form in containers exposed to fire at a risk of explosion. Do not breathe combustion products.

Use jets of water to cool the containers to prevent product decomposition and the development of substances potentially hazardous for health.

Block the leakage if there is no hazard. Send away individuals who are not suitably equipped.

The product must not penetrate into the sewer system or come into contact with surface water or ground water.

Collect the leaked product into a suitable container. Absorb the remainder with inert absorbent material.

Materials: inert absorbent material

Keep away from heat, sparks and naked flames; do not smoke or use matches or lighters. Without adequate ventilation, vapours may accumulate at ground level and, if ignited, catch fire even at a distance, with the danger of backfire. Avoid bunching of electrostatic charges. When performing transfer operations involving large containers, connect to an earthing system and wear antistatic footwear. Vigorous stirring and flow through the tubes and equipment may cause the formation and accumulation of electrostatic charges. In order to avoid the risk of fires and explosions, never use compressed air when handling. Open containers with caution as they may be pressurised. Do not eat, drink or smoke during use. Avoid leakage of the product into the environment.

Store only in the original container. Store the containers sealed, in a well ventilated place, away from direct sunlight. Store in a cool and well ventilated place, keep far away from sources of heat, naked flames and sparks and other sources of ignition.

Do not eat, drink or smoke during use.

Keep away from heat, sparks and naked flames; do not smoke or use matches or lighters. Avoid bunching of electrostatic charges. Vigorous stirring and flow through the tubes and equipment may cause the formation and accumulation of electrostatic charges. In order to avoid the risk of fires and explosions, never use compressed air when handling.

As the use of adequate technical equipment must always take priority over personal protective equipment, make sure that the workplace is well aired through effective local aspiration.

Protect hands with category III work gloves. The following should be considered when choosing work glove material (see standard EN 374): compatibility, degradation, failure time and permeability. The work gloves' resistance to chemical agents should be checked before use, as it can be unpredictable. The gloves' wear time depends on the duration and type of use. We recommend the use of protective gloves that guarantee total resistance in accordance with EN 374 and, in particular, they are resistant to the permeation of chemicals tested according to EN 374-3. Nitrile or PVA gloves for short-term contact (splash protection): 0.4 mm thickness with at least protection index and 2 corresponding to> 30 minutes of permeation according to EN 374. Nitrile or PVA gloves for one Prolonged contact: thickness 0.7 mm with the lowest protection rating 4 corresponding to> 120 minutes of permeation if it complies with EN 374. Due to the many types of gloves available on the market, it is advisable to observe the manufacturer's operating instructions. The information provided here is based on bibliographic data, information on the actions of the manufacturers, or by analogy with similar substances. In the presence of wear and tear, the gloves must be replaced.

Wear airtight protective goggles (see standard EN 166).

If the threshold value (e.g. TLV-TWA) is exceeded for the substance or one of the substances present in the product, wear a mask with a type AX filter, whose limit of use will be defined by the manufacturer (see standard EN 14387). In the presence of gases or vapours of various kinds and/or gases or vapours containing particulate (aerosol sprays, fumes, mists, etc.) combined filters are required. Respiratory protection devices must be used if the technical measures adopted are not suitable for restricting the worker's exposure to the threshold values considered. The protection provided by masks is in any case limited. If the substance considered is odourless or its olfactory threshold is higher than the corresponding TLV-TWA and in the case of an emergency, wear open-circuit compressed air breathing apparatus (in compliance with standard EN 137) or external air-intake breathing apparatus (in compliance with standard EN 138). For a correct choice of respiratory protection device, see standard EN 529.

Wear category II professional long-sleeved overalls and safety footwear (see Regulation 2016/425 and standard EN ISO 20344). Wash body with soap and water after removing protective clothing. Consider the appropriateness of providing antistatic clothing in the case of working environments in which there is a risk of explosion.

The emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure compliance with environmental standards. Product residues must not be indiscriminately disposed of with waste water or by dumping in waterways.

Formaldehyde: Acqueous solutions are stabilised with methanol. 1-methoxypropan-2-ol: stable. 2-methoxy-1-methylethyl acetate: Stable.

There are no particular risks of reaction with other substances in normal conditions of use.

Formaldehyde: tend to polymerise over time. 1-methoxypropan-2-ol: with air it may slowly form explosive peroxides. 2-methoxy-1-methylethyl acetate: with the air it may slowly develop peroxides that explode with an increase in temperature.

Formaldehyde: Decomposes under the effect of heat.

n-butyl acetate: Water, nitrates, strong oxidising agents, acids and alkalis and potassium tert-butoxide. Isobutyl acetate: Strong oxidising agents, nitrates, strong bases and acids. n-butanol: Nitric acid. Methanol: Plastics, magnesium, zinc alloys. Formaldehyde: Acids, akalis, ammonia, tannin, strong oxidising agents, phenols and copper, silver and iron salts. 1-methoxypropan-2-ol: Oxidising agents, strong acids and alkaline metals. 2-methoxy-1-methylethyl acetate: Oxidising agents, strong acids and alkaline metals. Hydrocarbons, C9, aromatics: Oxidizing agents. Xylene, mixture of isomers: Keep away from acidic and oxidizing materials.

Formaldehyde: Decomposes under the effect of heat.