HyGold 60/ BHT Blend

Move to fresh air. Oxygen or artificial respiration if needed. Do not use mouth-to-mouth method if victim inhaled the substance. Call a physician or poison control centre immediately.

Wash contact areas with soap and water. Remove contaminated clothing. Launder contaminated clothing before reuse. Get medical attention if irritation develops and persists.

Symptoms: Defatting of the skin.

Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.

Rinse mouth thoroughly. Do NOT induce vomiting. If vomiting occurs naturally, have victim lean forward to reduce risk of aspiration. Call a poison control centre immediately.

Symptoms: Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia.

Halon. Dry chemicals. Foam. Carbon dioxide (CO2). Water spray or fog.

Do not use a solid water stream as it may scatter and spread fire. Do not use water jet as an extinguisher, as this will spread the fire.

No unusual fire or explosion hazards noted.

Cool containers exposed to flames with water until well after the fire is out.

Keep unnecessary personnel away. Local authorities should be advised if significant spillages cannot be contained. Wear appropriate protective equipment and clothing during clean-up. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Do not touch or walk through spilled material. Ensure adequate ventilation.

Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area). Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.

Prevent further leakage or spillage if safe to do so. Prevent entry into waterways, sewer, basements or confined areas. Avoid discharge to the aquatic environment.

Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

Materials: vermiculite, dry sand, earth, absorbent material (e.g. cloth, fleece)

All handling to take place in well-ventilated area. Do not breathe dust/fume/gas/mist/vapours/spray. DO NOT handle, store or open near an open flame, sources of heat or sources of ignition. Protect material from direct sunlight. Do not get this material in contact with eyes. Avoid contact with skin. Do not get this material on clothing. Avoid prolonged exposure.

Store locked up. Keep away from heat, sparks and open flame. Store in a well-ventilated place.

Wash hands after handling and before eating. Remove and wash contaminated clothing promptly. Shower after work.

DO NOT handle, store or open near an open flame, sources of heat or sources of ignition.

Provide adequate ventilation, including appropriate local extraction, to ensure that the defined occupational exposure limit is not exceeded.

Chemical resistant gloves are recommended. If contact with forearms is likely wear gauntlet style gloves. Wear suitable gloves tested to EN374. When prolonged or frequent repeated contact occurs, Nitrile gloves may be suitable. (Breakthrough time of > 240 minutes.) For incidental contact/splash protection Neoprene, PVC gloves may be suitable.

Goggles/face shield are recommended.

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators.

Chemical/oil resistant clothing is recommended. Launder contaminated clothing before reuse.

Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. Fume scrubbers, filters or engineering modifications to the process equipment may be necessary to reduce emissions to acceptable levels.

Stable.

The product is stable and non-reactive under normal conditions of use, storage and transport.

Hazardous polymerisation does not occur.

Heat, flames and sparks. Avoid temperatures exceeding the flash point.

Strong oxidising agents.

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons.

Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner.

Collect and reclaim or dispose in sealed containers at licensed waste disposal site.