Argon

Remove victim to uncontaminated area wearing self contained breathing apparatus. Keep victim warm and rested. Call a doctor. Apply artificial respiration if breathing stopped

Symptoms: In high concentrations may cause asphyxiation. Symptoms may include loss of mobility/consciousness. Victim may not be aware of asphyxiation.

Adverse effects not expected from this product

Adverse effects not expected from this product

Ingestion is not considered a potential route of exposure

Water spray or fog

Do not use water jet to extinguish

Exposure to fire may cause containers to rupture/explode

Use fire control measures appropriate for the surrounding fire. Cool endangered receptacles with water spray jet from a protected position. If possible, stop flow of product. Use water spray or fog to knock down fire fumes if possible. If leaking do not spray water onto container. Water surrounding area (from protected position) to contain fire. Move containers away from the fire area if this can be done without risk.

Try to stop release. Act in accordance with local emergency plan. Stay upwind.

Try to stop release

The product must be handled in accordance with good industrial hygiene and safety procedures. Only experienced and properly instructed persons should handle gases under pressure. Consider pressure relief device(s) in gas installations. Ensure the complete gas system was (or is regularly) checked for leaks before use. Do not smoke while handling product. Use only properly specified equipment which is suitable for this product, its supply pressure and temperature. Do not breathe gas. Avoid release of product into atmosphere. Refer to supplier's container handling instructions. Do not allow backfeed into the container. Protect cylinders from physical damage; do not drag, roll, slide or drop. When moving cylinders, even for short distances, use a cart (trolley, hand truck, etc.) designed to transport cylinders. Leave valve protection caps in place until the container has been secured against either a wall or bench or placed in a container stand and is ready for use. If user experiences any difficulty operating cylinder valve discontinue use and contact supplier. Never attempt to repair or modify container valves or safety relief devices. Damaged valves should be reported immediately to the supplier. Keep container valve outlets clean and free from contaminants particularly oil and water. Replace valve outlet caps or plugs and container caps where supplied as soon as container is disconnected from equipment. Close container valve after each use and when empty, even if still connected to equipment. Never attempt to transfer gases from one cylinder/container to another. Never use direct flame or electrical heating devices to raise the pressure of a container. Do not remove or deface labels provided by the supplier for the identification of the cylinder contents. Suck back of water into the container must be prevented.

Observe all regulations and local requirements regarding storage of containers. Containers should not be stored in conditions likely to encourage corrosion. Containers should be stored in the vertical position and properly secured to prevent them from falling over. Keep container below 50°C in a well ventilated place.

The product must be handled in accordance with good industrial hygiene and safety procedures. Do not smoke while handling product.

Do not smoke while handling product. Never use direct flame or electrical heating devices to raise the pressure of a container.

Provide adequate general and local exhaust ventilation. Systems under pressure should be regularly checked for leakages. Oxygen detectors should be used when asphyxiating gases may be released. Consider the use of a work permit system e.g. for maintenance activities

Wear working gloves when handling gas containers. Standard EN 388 - Protective gloves against mechanical risk

Wear safety glasses with side shields. Standard EN 166 - Personal eye-protection - specifications

Self contained breathing apparatus (SCBA) or positive pressure airline with mask are to be used in oxygen-deficient atmospheres. Standard EN 137 - Self-contained open-circuit compressed air breathing apparatus with full face mask

Wear safety shoes while handling containers. Standard EN ISO 20345 - Personal protective equipment - Safety footwear

None necessary.

Stable under normal conditions

No reactivity hazard other than the effects described in sub-sections below

None under recommended storage and handling conditions (see section 7)

For additional information on compatibility refer to ISO 11114

May be vented to atmosphere in a well ventilated place

Do not discharge into any place where its accumulation could be dangerous

Avoid transport on vehicles where the load space is not separated from the driver's compartment. Ensure vehicle driver is aware of the potential hazards of the load and knows what to do in the event of an accident or an emergency. Before transporting product containers: Ensure there is adequate ventilation, Ensure that containers are firmly secured, Ensure cylinder valve is closed and not leaking, Ensure valve outlet cap nut or plug (where provided) is correctly fitted, Ensure valve protection device (where provided) is correctly fitted.

Avoid transport on vehicles where the load space is not separated from the driver's compartment. Ensure vehicle driver is aware of the potential hazards of the load and knows what to do in the event of an accident or an emergency. Before transporting product containers: Ensure there is adequate ventilation, Ensure that containers are firmly secured, Ensure cylinder valve is closed and not leaking, Ensure valve outlet cap nut or plug (where provided) is correctly fitted, Ensure valve protection device (where provided) is correctly fitted.

Avoid transport on vehicles where the load space is not separated from the driver's compartment. Ensure vehicle driver is aware of the potential hazards of the load and knows what to do in the event of an accident or an emergency. Before transporting product containers: Ensure there is adequate ventilation, Ensure that containers are firmly secured, Ensure cylinder valve is closed and not leaking, Ensure valve outlet cap nut or plug (where provided) is correctly fitted, Ensure valve protection device (where provided) is correctly fitted.