Resorcinol

Remove to fresh air. If not breathing, give artificial respiration. Get medical attention if symptoms occur.

Symptoms: trouble breathing, dizziness, lightheadedness

Wash off immediately with plenty of water for at least 15 minutes. If skin irritation persists, call a physician.

Symptoms: allergic skin reaction, rash, itching, swelling, tingling of the hands and feet

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Clean mouth with water and drink afterwards plenty of water. Get medical attention if symptoms occur.

Water spray. Carbon dioxide (CO₂). Dry chemical. Water mist may be used to cool closed containers. Chemical foam.

No information available.

Dust can form an explosive mixture with air. Containers may explode when heated. Fine dust dispersed in air may ignite.

Ensure adequate ventilation. Use personal protective equipment as required.

Do not flush into surface water or sanitary sewer system. Do not allow material to contaminate ground water system. Prevent product from entering drains.

Sweep up and shovel into suitable containers for disposal.

Materials: suitable containers

Do not get in eyes, on skin, or on clothing. Wear personal protective equipment/face protection. Ensure adequate ventilation. Avoid ingestion and inhalation. Avoid dust formation.

Keep in a dry, cool and well-ventilated place. Keep container tightly closed. Protect from direct sunlight. Store under an inert atmosphere. Protect from moisture.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing and gloves, including the inside, before re-use. Wash hands before breaks and after work.

Ensure adequate ventilation, especially in confined areas. Ensure that eyewash stations and safety showers are close to the workstation location. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Glove materials: Nitrile rubber, Neoprene, Natural rubber, PVC. EU standard: EN 374. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Ensure gloves are suitable for the task: Chemical compatability, Dexterity, Operational conditions, User susceptibility, e.g. sensitisation effects, also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Remove gloves with care avoiding skin contamination.

Goggles (European standard - EN 166)

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. To protect the wearer, respiratory protective equipment must be the correct fit and be used and maintained properly. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended Filter type: Particulates filter conforming to EN 143. Small scale/Laboratory use: Use a NIOSH/MSHA or European Standard EN 149:2001 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended half mask: Particle filtering: EN149:2001. When RPE is used a face piece Fit Test should be conducted

Wear appropriate protective gloves and clothing to prevent skin exposure. Inspect gloves before use.

Prevent product from entering drains. Do not allow material to contaminate ground water system. Local authorities should be advised if significant spillages cannot be contained.

Hygroscopic. Air sensitive. Light sensitive.

None known, based on information available

Hazardous polymerization does not occur. None under normal processing.

Avoid dust formation. Heat, flames and sparks. Excess heat. Exposure to air. Exposure to light. Incompatible products. Exposure to moist air or water.

Bases. Strong oxidizing agents. Alkaline. Acid anhydrides. Acid chlorides. Metals.

Carbon monoxide (CO). Carbon dioxide (CO₂).

Dispose of in accordance with the European Directives on waste and hazardous waste. Dispose of in accordance with local regulations.

Should not be released into the environment.