Ethylenediamine

Provide fresh air. In all cases of doubt, or when symptoms persist, seek medical advice.

Symptoms: Cough, Dyspnoea

After contact with skin, wash immediately with plenty of water.

Symptoms: Corrosion

In case of contact with eyes flush immediately with plenty of flowing water for 10 to 15 minutes holding eyelids apart and consult an ophthalmologist. Protect uninjured eye.

Symptoms: Risk of blindness, Risk of serious damage to eyes

Rinse mouth immediately and drink plenty of water. Rinse mouth with water (only if the person is conscious). Call a physician immediately.

Symptoms: If swallowed danger of perforation of the esophagus and the stomach (strong corrosive effects).

co-ordinate firefighting measures to the fire surroundings! water spray, alcohol resistant foam, dry extinguishing powder, BC-powder, carbon dioxide (CO₂)

water jet

Combustible. In case of insufficient ventilation and/or in use, may form flammable/explosive vapour-air mixture. Solvent vapours are heavier than air and may spread along floors. Places which are not ventilated, e.g. unventilated below ground level areas such as trenches, conduits and shafts, are particularly prone to the presence of flammable substances or mixtures. Vapours may form explosive mixtures with air.

Fight fire with normal precautions from a reasonable distance.

Use personal protective equipment as required. Avoid contact with skin, eyes and clothes. Do not breathe vapour/spray.

Keep away from drains, surface and ground water. Retain contaminated washing water and dispose of it.

Absorb with liquid-binding material (sand, diatomaceous earth, acid- or universal binding agents).

Materials: sand, diatomaceous earth, acid- or universal binding agents

Provision of sufficient ventilation. Handle and open container with care. Clear contaminated areas thoroughly.

Keep container tightly closed. Store locked up. Recommended storage temperature: 15 – 25 °C.

Thorough skin-cleansing after handling the product. When using do not smoke.

Keep away from sources of ignition - No smoking. Take precautionary measures against static discharge.

Wear suitable gloves. Chemical protection gloves are suitable, which are tested according to EN 374. Check leak-tightness/impermeability prior to use. For special purposes, it is recommended to check the resistance to chemicals of the protective gloves mentioned above together with the supplier of these gloves. The times are approximate values from measurements at 22 °C and permanent contact. Increased temperatures due to heated substances, body heat etc. and a reduction of the effective layer thickness by stretching can lead to a considerable reduction of the breakthrough time. If in doubt, contact manufacturer. At an approx. 1.5 times larger / smaller layer thickness, the respective breakthrough time is doubled / halved. The data apply only to the pure substance. When transferred to substance mixtures, they may only be considered as a guide. - type of material: Butyl caoutchouc (butyl rubber) - material thickness: 0,7 mm - breakthrough times of the glove material: >480 minutes (permeation: level 6) - Splash protection - Protective gloves - type of material: NBR (Nitrile rubber) - material thickness: 0,4 mm - breakthrough times of the glove material: >30 minutes (permeation: level 2)

Use safety goggle with side protection. Wear face protection.

Respiratory protection necessary at: Aerosol or mist formation. Type: A (against organic gases and vapours with a boiling point of >65 °C, colour code: Brown).

Take recovery periods for skin regeneration. Preventive skin protection (barrier creams/ointments) is recommended.

Keep away from drains, surface and ground water.

The material is stable under normal ambient and anticipated storage and handling conditions of temperature and pressure.

It's a reactive substance. Risk of ignition. If heated Risk of ignition. Vapours may form explosive mixtures with air.

Violent reaction with: Aldehydes, Alcohols, Halogenated hydrocarbons, Perchlorates, Exothermic reaction with: Acrylic acid, Acetic acid, Acetic anhydride, Oxidisers, Acids, Carbon disulfide, Hydrochloric gas

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

aluminium, iron, copper, bronze, brass, zinc

Hazardous combustion products: see section 5.

Dispose of contents/container in accordance with local/regional/national/international regulations.

This material and its container must be disposed of as hazardous waste.

Provisions for dangerous goods (ADR) should be complied within the premises.