NextSDS Logo
Safety Data Sheet EN

BRITE-MARK PAINT MARKER

Keep this SDS organized and up to date

Add this SDS to your NextSDS library and keep all its safety information in one place.

Add to my SDS library for free
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BRITE-MARK PAINT MARKER
Product Code
40003, 41003, 84002, 84202, 40001, 41001, 84001, 84201, 40007, 84010, 84051, 40004, 41004, 84007, 84207, 84008, 40010, 41010, 84005, 84205, 84009, 40002, 41002, 84006, 84206, 40016, 84050, 84019, 40008, 41008, 84003, 84203, 40006, 41006, 84004, 84204

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Solvent based marker

Uses advised against

No information available

Manufacturers & Suppliers

I

Importer

importer

(5511) 4785.2600

I

ITW PRO BRANDS

national supplier

805 E. Old 56 Highway, Olathe, KS 66061

1-800-443-9536

Emergency Contacts

Infotrac

800-535-5053

Emergency Contact

112

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Irrit. Cat. 2
Eye Irrit. Cat. 2
Muta. Cat. 1B
Carc. Cat. 1B
STOT SE Cat. 3
Aquatic Acute Cat. 1
Aquatic Chronic Cat. 1
Flam. Liq. Cat. 3

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

GHS09 - Environmental hazard

GHS09

Hazard Statements

H226 Flammable liquid and vapor
H315 Causes skin irritation
H319 Causes serious eye irritation
H335 May cause respiratory irritation. May cause drowsiness or dizziness
H336 May cause drowsiness or dizziness
H340 May cause genetic defects
H350 May cause cancer
H410 Very toxic to aquatic life with long lasting effects

Precautionary Statements

P201 Obtain special instructions before use
P202 Do not handle until all safety precautions have been read and understood
P210 Keep away from heat/sparks/open flames/hot surfaces. - No smoking
P233 Keep container tightly closed
P240 Ground/Bond container and receiving equipment
P241 Use explosion-proof electrical/ ventilating/ lighting/ equipment
P242 Use only non-sparking tools
P243 Take precautionary measures against static discharge
P261 Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray
P264 Wash face, hands and any exposed skin thoroughly after handling
P271 Use only outdoors or in a well-ventilated area
P273 Avoid release to the environment
P281 Use personal protective equipment as required
P302 + P352 IF ON SKIN: Wash with plenty of soap and water
P304 + P340 IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
P308 + P313 IF exposed or concerned: Get medical advice/ attention
P321 Specific treatment (see supplemental first aid instructions on this label)
P332 + P313 If skin irritation occurs: Get medical advice/ attention
P337 + P313 If eye irritation persists: Get medical advice/ attention
P362 Take off contaminated clothing and wash before reuse
P370 + P378 In case of fire: Use CO2, dry chemical, or foam for extinction.
P391 Collect spillage
P403 + P233 Store in a well-ventilated place. Keep container tightly closed
P403 + P235 Store in a well-ventilated place. Keep cool
P405 Store locked up
P501 Dispose of contents/ container to an approved waste disposal plant

Still copying SDS data manually?Free

You don't have to. NextSDS reads this SDS and adds the information to your library automatically.

Let NextSDS do it for me
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
n-Butyl acetate 123-86-4 70.104% Yes
Titanium dioxide EC: 236-675-5 13463-67-7 60.3511% No
Copper EC: 231-159-6 7440-50-8 19.296% Yes
Aluminum EC: 231-072-3 7429-90-5 13.936% Yes
Carbon black 1333-86-4 11.25% No
Isopropyl alcohol 67-63-0 6.968% Yes
Silicon dioxide 7631-86-9 6.9175% No
Zinc EC: 231-175-3 7440-66-6 6.432% Yes
Aluminum hydroxide EC: 244-492-7 21645-51-2 5.4085% No
Petroleum naphtha, light aromatic 64742-95-6 1.494% Yes
1,2,4 Trimethylbenzene 95-63-6 1.494% Yes
Zirconium oxide EC: 215-227-2 1314-23-4 0.6036% No
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Move to fresh air. If breathing is difficult, give oxygen. If symptoms persist, call a physician.

Skin contact

Wash off immediately with soap and plenty of water removing all contaminated clothes and shoes. If skin irritation persists, call a physician.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. If symptoms persist, call a physician. Keep eye wide open while rinsing.

Ingestion

Rinse mouth. Drink plenty of water. Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Consult a physician if necessary

Immediate Medical Attention

Immediate medical attention is required.

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Dry chemical. Carbon dioxide (CO₂). Foam.

Unsuitable media

Water.

Specific hazards

Most vapors are heavier than air. They will spread along ground and collect in low or confined areas (sewers, basements, tanks).

Firefighter Protection

As in any fire, wear self-contained breathing apparatus and full protective gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Remove all sources of ignition. Evacuate personnel to safe areas. Ensure adequate ventilation. Use personal protective equipment. Stop leak if you can do it without risk.

Small spill

Use a non-combustible material like vermiculite, sand or earth to soak up the product and place into a container for later disposal.

Large spill

Pump or vacuum transfer spilled product to clean containers for recovery. Absorb unrecoverable product.

Environmental

Prevent further leakage or spillage if safe to do so.

Cleanup methods

Use a non-combustible material like vermiculite, sand or earth to soak up the product and place into a container for later disposal. Pump or vacuum transfer spilled product to clean containers for recovery. Absorb unrecoverable product.

—

Related Products

Similar products with comparable safety profiles

M

MARKER PEN - Red

UFI: 8VGY-78AJ-A00C-RUJ5

M

MARKER PEN - Yellow

UFI: WAHY-R8SH-U00U-1JFG

P

Pro-Line® HP Paint Markers

---

A

Artline Permanent Marker

---

M

MORTRACE™ SB LIQUID MARKER

---

C

COLORMARK LINEMARKER GREEN 500 ML

---

C

COLORMARK LINEMARKER WHITE 500 ML

---

C

COLORMARK LINEMARKER BLUE 500 ML

---

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Ensure adequate ventilation. Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharges. Use only in an area containing flame proof equipment. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded. Avoid contact with skin, eyes and clothing. Empty containers pose a potential fire and explosion hazard. Do not cut, puncture or weld containers.

Storage

Keep containers tightly closed in a cool, well-ventilated place.

Hygiene

When using, do not eat, drink or smoke. Provide regular cleaning of equipment, work area and clothing.

Fire prevention

Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharges. Use only in an area containing flame proof equipment.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Ensure adequate ventilation, especially in confined areas.

Hands

Chemical resistant gloves

Eyes

Safety glasses with side-shields. If splashes are likely to occur, wear: Chemical splash goggles.

Respiratory

No special protective equipment required. If exposure limits are exceeded or irritation is experienced, approved respiratory protection should be worn.

Skin/Body

Risk of contact: Boots. Apron.

Environmental

Do not allow material to contaminate ground water system.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Language Code
---
Physical State
Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
Opaque, Varies.
Colour
---
Colour Intensity
---
Form
---
Odor
Sweet
Odor Threshold
---
Ph
No data available
Melting Point
No data available
Boiling Point
122.2 °C / 252 °F
Flash Point
Tag closed cup: 27.2 °C / 81 °F
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
< 1 (BuAc = 1)
Vapor Pressure
No data available
Vapor Density
No data available
Relative Density
> 1 @ 70°F
Bulk Density
---
Density
---
Flammability
Flammable; may be ignited by heat, sparks or flames.
Upper Explosive Limit
7.6
Lower Explosive Limit
1.7
Explosive Limits
---
Auto Ignition Temperature
No data available
Decomposition Temperature
No data available
Solubility
---
Partition Coefficient
---
Solubility In Water
Slightly soluble
Solubility In Fat
---
Molecular Weight
---
Voc Content
A720M Black: 66.61%, A786M Brown: 67.78%, A789M Green: 69.77%, A787M Pink: 48.62%, A945M Silver: 71.68%, A718M White: 47.85%, A788M Blue: 68.83%, A946M Gold: 59.75%, A783M Light Blue: 50.34%, A790M Orange: 65.48%, A791M Red: 66.17%, A785M Violet: 76.57%, A719M Yellow: 68.20%
Metal Corrosion
---
Dynamic Viscosity
---
Kinematic Viscosity
---
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions.

Reactivity

No data available.

Hazardous reactions

None under normal processing.

Avoid

Heat, flames and sparks. Incompatible products.

Incompatible

Strong oxidizing agents. Strong reducing agents. Strong alkalis. Strong acids.

Decomposition

Carbon oxides. Soot. Smoke

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

12.1. Toxicity

12.2 Persistence and degradability

12.3 Bioaccumulative potential

12.4 Mobility in soil

12.5 Results of PBT and vPvB assessment

12.6 Endocrine disrupting properties

12.7 Other adverse effects

12.1. Toxicity

Ecotoxicity Effects Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. | Chemical Name | Toxicity to Algae | Toxicity to Fish | Toxicity to Microorganisms | Daphnia Magna (Water Flea) | | --- | --- | --- | --- | --- |

The substance is described as very toxic to aquatic organisms with potential long-term adverse effects in the aquatic environment.

12.1. Toxicity

| Chemical Name | Toxicity to Algae | Toxicity to Fish | Toxicity to Microorganisms | Daphnia Magna (Water Flea) | | --- | --- | --- | --- | --- | | n-Butyl acetate | EC50 72 h: = 674.7 mg/L (Desmodesmus subspicatus) | LC50 96 h: 17 - 19 mg/L flow-through (Pimephales promelas) LC50 96 h: = 100 mg/L static (Lepomis macrochirus) LC50 96 h: = 62 mg/L static (Leuciscus idus) | EC50 = 70.0 mg/L 5 min EC50 = 82.2 mg/L 15 min EC50 = 959 mg/L 18 h EC50 = 98.9 mg/L 30 min | EC50 24 h: = 72.8 mg/L (Daphnia magna) |

12.1. Toxicity

Copper | EC50 96 h: 0.031 - 0.054 mg/L static (Pseudokirchneriella subcapitata) EC50 72 h: 0.0426 - 0.0535 mg/L static (Pseudokirchneriella subcapitata) | LC50 96 h: 0.0068 - 0.0156 mg/L (Pimephales promelas) LC50 96 h: < 0.3 mg/L static (Pimephales promelas) LC50 96 h: = 0.052 mg/L flow-through (Oncorhynchus mykiss) LC50 96 h: = 0.112 mg/L flow-through (Poecilia reticulata) LC50 96 h: = 0.2 mg/L flow-through (Pimephales promelas) LC50 96 h: = 0.3 mg/L semi-static (Cyprinus carpio) LC50 96 h: = 0.8 mg/L static (Cyprinus carpio) LC50 96 h: = 1.25 mg/L static (Lepomis macrochirus) | - | EC50 48 h: = 0.03 mg/L Static (Daphnia magna)

12.1. Toxicity

| Carbon black | | | | EC50 24 h: > 5600 mg/L (Daphnia magna) |

12.1. Toxicity

EC50 96 h: > 1000 mg/L (Desmodesmus subspicatus) EC50 72 h: > 1000 mg/L (Desmodesmus subspicatus) LC50 96 h: = 11130 mg/L static (Pimephales promelas) LC50 96 h: = 9640 mg/L flow-through (Pimephales promelas) LC50 96 h: > 1400000 µg/L (Lepomis macrochirus) EC50 48 h: = 13299 mg/L (Daphnia magna)

12.1. Toxicity

| Silicon dioxide | EC50 72 h: = 440 mg/L (Pseudokirchneriella subcapitata) | LC50 96 h: = 5000 mg/L static (Brachydanio rerio) | | EC50 48 h: = 7600 mg/L (Ceriodaphnia dubia) |

12.1. Toxicity

Zinc EC50 72 h: 0.09 - 0.125 mg/L static (Pseudokirchneriella subcapitata) EC50 96 h: 0.11 - 0.271 mg/L static (Pseudokirchneriella subcapitata) LC50 96 h: 0.211-0.269 mg/L semi-static (Pimephales promelas) LC50 96 h: 2.16-3.05 mg/L flow-through (Pimephales promelas) LC50 96 h: = 0.24 mg/L flow-through (Oncorhynchus mykiss) LC50 96 h: = 0.41 mg/L static (Oncorhynchus mykiss) LC50 96 h: = 0.45 mg/L semi-static (Cyprinus carpio) LC50 96 h: = 0.59 mg/L semi-static (Oncorhynchus mykiss) LC50 96 h: = 2.66 mg/L static (Pimephales promelas) LC50 96 h: = 3.5 mg/L static (Lepomis macrochirus) LC50 96 h: = 30 mg/L (Cyprinus carpio) LC50 96 h: = 7.8 mg/L static (Cyprinus carpio) EC50 48 h: 0.139 - 0.908 mg/L Static (Daphnia magna)

12.1. Toxicity

LC50 96 h: = 9.22 mg/L (Oncorhynchus mykiss) EC50 48 h: = 6.14 mg/L (Daphnia magna)

12.1. Toxicity

| 1,2,4 Trimethylbenzene | | LC50 96 h: 7.19 - 8.28 mg/L flow-through (Pimephales promelas) | | EC50 48 h: = 6.14 mg/L (Daphnia magna) |

12.2. Persistence and degradability

No information available.

12.3. Bioaccumulative potential.

| Chemical Name | Log Pow | | --- | --- |

12.3. Bioaccumulative potential.

| Chemical Name | Log Pow | | --- | --- | | n-Butyl acetate | 1.81 |

12.3. Bioaccumulative potential.

| Chemical Name | Log Pow | | --- | --- | | Isopropyl alcohol | 0.05 |

12.3. Bioaccumulative potential.

| Chemical Name | Log Pow | | --- | --- | | 1,2,4 Trimethylbenzene | 3.63 |

12.4. Mobility in soil

Adsorbs on soil.

12.5. Results of PBT and vPvB assessment

No information available.

12.6. Other adverse effects

This product does not contain any known or suspected endocrine disruptors.

The product does not contain any known or suspected endocrine disruptors.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Disposal

Dispose of in accordance with local regulations.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1263
Shipping Name
Paint
Transport Class
3
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BRITE-MARK PAINT MARKER?

The signal word is danger.

What is the physical form of BRITE-MARK PAINT MARKER?

BRITE-MARK PAINT MARKER is a liquid appearing as opaque, varies. . It has sweet odor.

What is BRITE-MARK PAINT MARKER used for?

Solvent based marker

What are the hazard statements for BRITE-MARK PAINT MARKER?

This substance has 8 hazard statements:

  • H226: Flammable liquid and vapor
  • H315: Causes skin irritation
  • H319: Causes serious eye irritation
  • H335: May cause respiratory irritation. May cause drowsiness or dizziness
  • H336: May cause drowsiness or dizziness
  • H340: May cause genetic defects
  • H350: May cause cancer
  • H410: Very toxic to aquatic life with long lasting effects

What is the melting point of BRITE-MARK PAINT MARKER?

The melting point is No data available and the boiling point is 122.2 °C / 252 °F.