Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MOL Spinol 3 spindle oil
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
spindle oil for industrial and professional use.
Uses advised against
application other than the above, or population use.
Manufacturers & Suppliers
MOL-LUB Lubricant Production Distribution and Service Ltd.
manufacturer
H-2931 Almásfüzitő, Fő út 21., Hungary
+36 34 526 330
MOL-LUB Lubricant Production Distribution and Service Ltd. Customer Service Center
distributor
H-2931 Almásfüzitő, Fő út 21., Hungary
+36 80 201 296
MOL-LUB Ltd.
manufacturer
+36 80 201 296
Emergency Contacts
Emergency Contact
+36 34 526 210
on workdays: 07-15²⁰ h (CET)
Health Toxicological Information Service (ETTSZ 1097 Budapest, Albert Flórián st. 2-6.)
+36 80 201 199
0-24 h
Health Toxicological Information Service (ETTSZ 1097 Budapest, Albert Flórián st. 2-6.)
+36 1 476 6464
0-24 h
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of refined mineral base oils containing additives.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Hydrocarbons, C15-C20, n-alkanes, isoalkanes, cyclics,< 0.03% aromatics EC: 934-956-3 | --- | 85% | Yes |
| Distillates (petroleum), hydrotreated light paraffinic EC: 265-158-7 | 64742-55-8 | 85% | Yes |
| Hydrocarbons, C10-C13, n-alkanes, isoalkanes, cyclics, <2% aromatics EC: 918-481-9 | --- | 20% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove the affected person to fresh air. If rapid recovery does not occur, obtain medical attention.
Wash skin with large amounts of water, use soap. In case of persistent irritation, get medical attention.
Flush eyes with plenty of water for 10-15 minutes. In case of persistent irritation, get medical attention.
If swallowed, DO NOT induce vomiting. Get prompt medical attention.
Immediate Medical Attention
If swallowed.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Not required.
Oil resistant gloves (EN 374, Breakthrough time 480 min) (e.g. nitrile rubber - minimal thickness 0.33 mm). Note: Manufacturer's directions for use and the conditions of application should be observed.
Where splashing is possible, wear safety glasses (EN 166).
Under normal conditions not required. In case of exceeded exposure-limits respiratory protection with particle-filter is recommended.
Protective clothing (oil resistant) (EN 340).
Do not discharge into drains/surface waters/groundwater.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MOL Spinol 3 spindle oil?
The signal word is danger.
What is the physical form of MOL Spinol 3 spindle oil?
MOL Spinol 3 spindle oil is a liquid appearing as light yellow, bright, clear with light yellow, bright, clear color. It has characteristic odor.
What is the solubility of MOL Spinol 3 spindle oil?
practically insoluble in water gasoline, kerosene, toluene, etc.
What is MOL Spinol 3 spindle oil used for?
spindle oil for industrial and professional use.
What are the hazard statements for MOL Spinol 3 spindle oil?
This substance has 1 hazard statement:
- H304: May be fatal if swallowed and enters airways.
What is the melting point of MOL Spinol 3 spindle oil?
The melting point is typ. - 15°℃ and the boiling point is not available.