Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- CUT 'N DRY Sorptive Dust Insecticide
- Product Code
- 3002
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Insecticide dust for control of insects in stored grain.
Manufacturers & Suppliers
Grow Choice Pty Ltd
supplier
113 Fitzroy Street | TAMWORTH NSW 2340
02 6766 3979
http://www.chw.edu.au/poisons/contact.htm
Emergency Contacts
Emergency Contact
000
Poisons Information Centre
13 11 26
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Diathomaceous earth (Silica-Amorphous) EC: 612-383-7 | 61790-53-2 | 100% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move affected person to fresh air and keep at rest until recovered. Drink a glass of water to clear throat and blow nose to evacuate dust.
Symptoms: If irritation persists see a doctor or if at all worried.
Remove contaminated clothing and wash affected areas thoroughly with soap and water.
Symptoms: If irritation develops and persists or are concerned.
Wash it out immediately with water for several minutes. Seek medical attention.
Symptoms: If product gets in eyes, remove contact lenses if wearing and wash it out immediately with water for several minutes.
Rinse mouth out with water if patient is conscious.
Symptoms: If swallowed, DO NOT induce vomiting.
Immediate Medical Attention
Seek medical attention if irritation develops and persists or are concerned.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use local exhaust ventilation to keep exposure levels below the exposure limits above.
Elbow-length chemical resistant PVC gloves. Gloves: AS/NZS 2161, Industrial safety gloves and mittens (not electrical and medical gloves).
Face shield or goggles. Goggles and face shield AS/NZS 1337, Eye protectors for industrial applications.
If airborne concentrations are likely to exceed the exposure standards above or if exposed to dust, an AS/NZS 1715/1716 approved respirator should be worn. Respirators: AS NZS 1715 Selection, Use and Maintenance of Respiratory Protective Devices AS/NZS 1716, Respiratory Protective Devices.
Cotton overalls buttoned to the neck and wrist (or equivalent clothing) and a washable hat. Overalls: AS 3765, Clothing for protection against Hazardous chemicals.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for CUT 'N DRY Sorptive Dust Insecticide?
The signal word is no signal word.
What is the physical form of CUT 'N DRY Sorptive Dust Insecticide?
CUT 'N DRY Sorptive Dust Insecticide is a solid appearing as white to light grey coloured dust with no odour (non-crystalline) with white to light grey color. It has no odour odor.
What is CUT 'N DRY Sorptive Dust Insecticide used for?
Insecticide dust for control of insects in stored grain.
What is the melting point of CUT 'N DRY Sorptive Dust Insecticide?
The melting point is 1500℃ and the boiling point is Not applicable..