Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Microcare PE
Regulatory Identifiers
- CAS Number
- 122-99-6 Check regulations →
- EC Number
- 204-589-7 Check regulations →
Identified Uses
Additive for the cosmetic industry.
Manufacturers & Suppliers
Thor Specialties Sdn Bhd
manufacturer
Jalan Bursa 23/4, 40300 Shah Alam, Selangor Darul Ehsan, Malaysia
+60 3 5542 5788
Emergency Contacts
Emergency Contact
+60 3 5542 5788
Transport-Accident-Information and Emergency-Response-System
+49 621 6043333
24 h service
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2-Phenoxyethanol EC: 204-589-7 | 122-99-6 | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air.
Wash with plenty of soap and water.
Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Consult an eye specialist.
Rinse mouth. Do NOT induce vomiting. Seek medical treatment.
Immediate Medical Attention
If swallowed, gastric irrigation with activated carbon.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
In case of contamination devices to rinse eyes or skin immediately under running water must be available.
Chemical protective gloves (EN ISO 374-1:2016). Wear protective gloves with long gauntlets preferably. Check the condition of protective gloves after each use for any damages like holes, cuts or tears. After use of gloves apply skin-cleaning agents and skin cosmetics. Do not wear protective gloves longer than necessary. Material of gloves: Nitrile rubber, NBR. Penetration time of glove material: Thickness: 0.4 mm; break-through time: 480 min; material: Nitrile; permeation: level 6. Gloves made of the following materials are not suitable: Gloves for mechanical protection do not provide protection against chemicals.
Safety glasses (EN 166)
When there is potential for airborne exposures: Respirator with filter for use against organic gases and vapours, boiling point above 65 ℃ and particles (EN 14387).
Protective clothing (EN 14605:2009-08)
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Microcare PE?
The signal word is danger.
What is the physical form of Microcare PE?
Microcare PE is a liquid appearing as colourless clear with colourless clear color. It has weak, characteristic odor.
What is the solubility of Microcare PE?
24.17 g/l
What is Microcare PE used for?
Additive for the cosmetic industry.
What are the hazard statements for Microcare PE?
This substance has 3 hazard statements:
- H302: Harmful if swallowed.
- H318: Causes serious eye damage.
- H335: May cause respiratory irritation.
What is the melting point of Microcare PE?
The melting point is 10.9 °C and the boiling point is 243.2 °C.