Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MAPEFLEX P2 SL / A
- Product Code
- 9019101
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Polyurethane-based adhesive
Uses advised against
Not available
Manufacturers & Suppliers
MAPEI CORP. (USA and Puerto Rico)
manufacturer
1144 East Newport Center Drive, 33442 - Deerfield Beach - FL - USA
954-246-8888
Emergency Contacts
CANUTEC
1-613-996-6666
CHEMTREC
1(800) 424-9300
24 hours
CHEMTREC
1(703) 527-3887
24 hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Hazardous components within the meaning of 29 CFR 1910.1200 and related classification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| titanium dioxide EC: 236-675-5 | 13463-67-7 | 2.5 - 5% | Yes |
| calcium oxide EC: 215-138-9 | 1305-78-8 | 2.5 - 5% | Yes |
| xylene EC: 215-535-7 | 1330-20-7 | 1 - 2.5% | Yes |
| ethylbenzene EC: 202-849-4 | 100-41-4 | 0.49 - 1% | Yes |
| bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacate EC: 255-437-1 | 41556-26-7 | 0.1 - 0.25% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove casualty to fresh air and keep warm and at rest.
Immediately take off all contaminated clothing. OBTAIN IMMEDIATE MEDICAL ATTENTION. Obtain medical attention if skin related symptoms persist. Remove contaminated clothing immediately and dispose of safely. After contact with skin, wash immediately with soap and plenty of water.
After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an ophthalmologist immediately. Protect uninjured eye.
Do not induce vomiting, get medical attention showing the SDS and the hazard label.
Immediate Medical Attention
In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible).
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Not available
Suitable materials for safety gloves; 29 CFR 1910.138 - ANSI/ISEA 105: Polychloroprene - CR: thickness >=0.5mm; breakthrough time >=480min. Nitrile rubber - NBR: thickness >=0.35mm; breakthrough time >=480min. Butyl rubber - IIR: thickness >=0.5mm; breakthrough time >=480min. Fluorinated rubber - FKM: thickness >=0.4mm; breakthrough time >=480min. Use impervious gloves that provides comprehensive protection, e.g. P.V.C., neoprene or rubber.
Use close fitting safety goggles, don't use eye lens.
Respiratory protection must be used where exposure levels exceed workplace exposure limits. Refer to 29 CFR 1910.134 - CSA Z94.4 for information on selection and use of appropriate respiratory protection equipment.
Use clothing that provides comprehensive protection to the skin, e.g. cotton, rubber, PVC or viton.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1993
- Shipping Name
- Flammable liquids, n.o.s. (xylene - ethylbenzene)
- Transport Class
- 3
- Packing Group
- III
B1, B52, IB3, T4, TP1, TP29
223 274 955
A3
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MAPEFLEX P2 SL / A?
The signal word is warning.
What is the physical form of MAPEFLEX P2 SL / A?
MAPEFLEX P2 SL / A is a liquid appearing as paste with grey color. It has like: xylene odor.
What is MAPEFLEX P2 SL / A used for?
Polyurethane-based adhesive
What are the hazard statements for MAPEFLEX P2 SL / A?
This substance has 3 hazard statements:
- H226: Flammable liquid and vapour.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
What is the melting point of MAPEFLEX P2 SL / A?
The melting point is No data available and the boiling point is No data available.