NextSDS Logo
Safety Data Sheet EN

OdoBan Ready-to-Use Original Eucalyptus Scent

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
OdoBan Ready-to-Use Original Eucalyptus Scent
Synonyms
None.

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Disinfectant (non-aerosol)

Uses advised against

None known.

Manufacturers & Suppliers

C

Clean Control Corporation c/o MacIsaac & Associates

manufacturer

440 Gloucester Street, Suite 2111, Ottawa, ON K1R 7T8, Canada

613-236-2250

Emergency Contacts

CHEMTREC

1-800-262-8200 (U.S.)

CHEMTREC

1-703-741-5500 (International)

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Skin Irrit. Cat. 2
Eye Irrit. Cat. 2B

GHS Pictograms

GHS07 - Health hazard

GHS07

Hazard Statements

H315 Causes skin irritation.
H320 Causes eye irritation.

Precautionary Statements

P234 Store away from incompatible materials.
P264 Wash thoroughly after handling.
P280 Wear protective gloves.
P321 Specific treatment (see information on this label).
P332 + P313 If skin irritation occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P338 Remove contact lenses, if present and easy to do.
P338 Continue rinsing.
P351 IF IN EYES: Rinse cautiously with water for several minutes.
P352 IF ON SKIN: Wash with plenty of water.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P501 Dispose of container in accordance with local, regional, national and international regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Alkyl (C14 50%, C12 40%, C16 10%) dimethyl benzyl ammonium chloride 68424-85-1 0.3% No

All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume.

Notes

Not applicable to DIN products. Refer to product label for active ingredient content.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If symptoms develop move victim to fresh air. If symptoms persist, obtain medical attention.

Skin contact

Wash with plenty of soap and water.

Symptoms: Skin irritation. May cause redness and pain.

Eye contact

If splashed in eyes, flush with water for 15 minutes. If irritation persists, seek medical attention.

Symptoms: Irritation of eyes. Exposed individuals may experience eye tearing, redness and discomfort.

Ingestion

Do not induce vomiting. Drink large quantities of milk or water. Obtain medical attention or contact a poison control centre immediately. Take container, label or product name and DIN Number with you when seeking medical attention.

Immediate Medical Attention

Obtain medical attention or contact a poison control centre immediately.

Medical Treatment

Provide general supportive measures and treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water fog. Foam. Dry chemical powder. Carbon dioxide.

Unsuitable media

Do not use water jet as an extinguisher, as this will spread the fire.

Specific hazards

During fire, gases hazardous to health may be formed.

Instructions

Move containers from fire area if you can do so without risk.

Firefighter Protection

Self-contained breathing apparatus and full protective clothing must be worn in case of fire.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ensure adequate ventilation. Local authorities should be advised if significant spillages cannot be contained.

Small spill

Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

Large spill

Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.

Environmental

Avoid discharge into drains, water courses or onto the ground. Do not discharge into lakes, streams, ponds or public waters.

Cleanup methods

Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

Materials: vermiculite, dry sand, earth, absorbent material (e.g. cloth, fleece)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin, and clothing. Provide adequate ventilation. Wear appropriate personal protective equipment. Wash thoroughly after handling. Use good industrial hygiene practices in handling this material. When using do not eat or drink.

Storage

Store in a cool dry place. Store in original tightly closed container. Keep out of reach of children.

Hygiene

Wash thoroughly after handling. Use good industrial hygiene practices in handling this material. When using do not eat or drink.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.

Hands

Impervious gloves. Confirm with reputable supplier first.

Eyes

Wear safety glasses with side shields.

Respiratory

Where exposure guideline levels may be exceeded, use an approved NIOSH respirator. Respirator should be selected by and used under the direction of a trained health and safety professional following requirements found in OSHA's respirator standard (29 CFR 1910.134), CAN/CSA-Z94.4 and ANSI's standard for respiratory protection (Z88.2).

Skin/Body

Wear appropriate chemical resistant clothing. As required by employer code.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Melting Point
Not available.
Form
Liquid.
Softening Point
---
Lower Explosive Limit
Not available.
Odor Threshold
Not available.
Solidification Point
---
Cloud Point
---
Auto Ignition Temperature
Not available.
Odor
Floral
Appearance
Clear
Decomposition Temperature
Not available.
Solubility
---
Flash Point
>93.3 °C (>200.0 °F)
Physical State Data
liquid
Colour Intensity
---
Molecular Weight
---
State Under Standard Conditions
---
Partition Coefficient
Not available.
Density
---
Metal Corrosion
---
Solubility In Fat
---
Relative Density
Not available.
Vapor Density
Not available.
Colour
Pale yellow
Dynamic Viscosity
---
Upper Explosive Limit
Not available.
Physical State
Liquid.
Bulk Density
---
Freezing Point
Not available.
Properties Status
---
Crystallisation Point
---
Evaporation Rate
Not available.
Boiling Point
>35 °C (>95 °F)
Explosive Limits
---
Ph
6 - 8
Voc Content
---
Vapor Pressure
Not available.
Kinematic Viscosity
---
Flammability
Not applicable.
Solubility In Water
Not available.
Relative Evaporation Rate
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under recommended storage conditions.

Reactivity

This product may react with strong oxidising agents.

Hazardous reactions

No dangerous reaction known under conditions of normal use.

Avoid

Avoid temperatures exceeding the flash point. Do not mix with other chemicals.

Incompatible

Strong oxidising agents.

Decomposition

May include and are not limited to: Oxides of carbon. Oxides of nitrogen. Hydrogen chloride.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Treatment

Dispose of in accordance with local regulations.

Disposal

Dispose of contents/container in accordance with local/regional/national/international regulations.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

This product is not subject to the Hazardous Products Act (HPA) Part II (Hazardous Products) as per paragraph 12(j); Schedule 1 (Non-Application of Part II).

Chemical Safety Assessment Not performed
?

Frequently Asked Questions

Common questions about safety, handling, and properties

What other names is OdoBan Ready-to-Use Original Eucalyptus Scent known by?

OdoBan Ready-to-Use Original Eucalyptus Scent is also known as: None.

What is the hazard signal word for OdoBan Ready-to-Use Original Eucalyptus Scent?

The signal word is warning.

What is the physical form of OdoBan Ready-to-Use Original Eucalyptus Scent?

OdoBan Ready-to-Use Original Eucalyptus Scent is a liquid. appearing as clear with pale yellow color. It has floral odor.

What is OdoBan Ready-to-Use Original Eucalyptus Scent used for?

Disinfectant (non-aerosol)

What are the hazard statements for OdoBan Ready-to-Use Original Eucalyptus Scent?

This substance has 2 hazard statements:

  • H315: Causes skin irritation.
  • H320: Causes eye irritation.

What is the melting point of OdoBan Ready-to-Use Original Eucalyptus Scent?

The melting point is Not available. and the boiling point is >35 °C (>95 °F).