Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE MR 5922 known as Loctite 5922
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Sealant
Manufacturers & Suppliers
Henkel Ltd
manufacturer
Wood Lane End, HP2 4RQ Hemel Hempstead, Great Britain
+44 1442 278000
Emergency Contacts
Emergency Contact
+44 (0)1442 278497
24 Hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Declaration of the ingredients according to CLP (EC) No 1272/2008
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| rosin EC: 232-475-7 | 8050-09-7 | 10 - 20% | Yes |
| Propan-2-ol EC: 200-661-7 | 67-63-0 | 10 - 20% | Yes |
| Titanium dioxide EC: 236-675-5 | 13463-67-7 | 1 - 5% | No |
Notes
For full text of the H - statements and other abbreviations see section 16 "Other information". Substances without classification may have community workplace exposure limits available.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms persist, seek medical advice.
Rinse with running water and soap. Obtain medical attention if irritation persists.
Symptoms: Rash, Urticaria.
Rinse immediately with plenty of running water (for 10 minutes), seek medical attention from a specialist.
Symptoms: Irritation, conjunctivitis.
Rinse mouth, drink 1-2 glasses of water, do not induce vomiting, consult a doctor.
Immediate Medical Attention
See section: Description of first aid measures
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, extinguishing powder, carbon dioxide.
None known
In the event of a fire, carbon monoxide (CO), carbon dioxide (CO2) and nitrogen oxides (NOx) can be released. Vapours may accumulate in low or confined areas, travel considerable distance to source of ignition, and flash back.
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not empty into drains / surface water / ground water.
Scrape up as much material as possible. Sweep up spilled material.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Vapours should be extracted to avoid inhalation. Use only in well-ventilated areas. Avoid skin and eye contact. See advice in section 8
Refer to Technical Data Sheet
Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working. Good industrial hygiene practices should be observed.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure good ventilation/extraction.
Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness). Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness). This information is based on literature references and on information provided by glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of chemical-resistant protective gloves may be considerably shorter than the permeation time determined in accordance with EN 374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should be replaced.
Safety glasses with sideshields or chemical safety goggles should be worn if there is a risk of splashing. Protective eye equipment should conform to EN166.
Ensure adequate ventilation. An approved mask or respirator fitted with an organic vapour cartridge should be worn if the product is used in a poorly ventilated area. Filter type: A (EN 14387)
Wear suitable protective clothing. Protective clothing should conform to EN 14605 for liquid splashes or to EN 13982 for dusts.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Strong oxidizing agents.
See section reactivity
Stable under normal conditions of storage and use. Heat, flames, sparks and other sources of ignition.
See section reactivity.
carbon oxides. aldehydes.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of according to regulations. Do not empty into drains / surface water / ground water.
Dispose of according to regulations.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE MR 5922 known as Loctite 5922?
The signal word is warning.
What is the physical form of LOCTITE MR 5922 known as Loctite 5922?
LOCTITE MR 5922 known as Loctite 5922 is a paste appearing as paste, pasty, black with black color. It has characteristic odor.
What is the solubility of LOCTITE MR 5922 known as Loctite 5922?
No data available / Not applicable
What is LOCTITE MR 5922 known as Loctite 5922 used for?
Sealant
What are the hazard statements for LOCTITE MR 5922 known as Loctite 5922?
This substance has 2 hazard statements:
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
What is the melting point of LOCTITE MR 5922 known as Loctite 5922?
The melting point is No data available / Not applicable and the boiling point is 82 °C (179.6 °F).